How to Select the Correct Hub to Change Out a 4 on 9.44 Inch Bolt Circle Wheels with 5 on 4-1/2
Updated 01/05/2011 | Published 01/04/2011
Products Featured in This Question
Question:
I have an older trailer with 4 bolt 9.44 bolt circle Hubei and wheels. I want to upgrade to 5 x4.5 hub configuration so I can get better rims and balance the tires. 3500 pound axle with 10 drums. I have measured the axle diameters bearing and seal diameters and they match your 3500 pound spindle numbers and the bearing diameter specs. Will a standard 1750 pound hub and drum fit. I am concerned about the spacing of the bearings in the hub. Thx.
asked by: Matt
Expert Reply:
It sounds as if you have taken all of the correct measurements to determine the correct hub and drum assembly for your trailer. Normally the spacing of the bearings is not an issue, as long as the axle used on the trailer is not an Agricultural axle or a mobile home axle.
The Trailer Hub & Drum Assembly, item # AKHD-545-35-EZ-K, is designed to be used with the EZ Lube Spindle for 3,500 lb axle, item # TRU74FR. The dimensions of this spindle are as follows.
Seal diameter - 1.73 inches
Inner Bearing diameter - 1.38 inches
Outer bearing diameter - 1.06 inches
If the dimensions on your axle match these dimensions then the 1750 lbs # AKHD-545-35-EZ-K hub assembly should work fine on your trailer. If not let me know the measurements you have taken and we can try to find the correct hub and drum assembly for your trailer.
If you cannot come up with a hub and drum assembly that will fit your trailer we do have wheels to match your 4 bolt 9.44 bolt circle. I have added a link to all of the vintage replacement wheels that we carry for you to review.
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Drum
- EZ Lube
- Pre-Greased
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: 4 on 944 inch trailer tires and wheels
- Q&A: Replacement Hub/Drum Assembly Needed for a Dexter 8-147 Assembly
- Shop: Aluminum AM01 Series Gunmetal Machined Trailer Wheel - 12" x 4" Rim - 5 on 4-1/2
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Dexstar Steel Mini Mod Trailer Wheel - 14" x 5-1/2" Rim - 5 on 4-1/2 - Black
- Q&A: Is The 4 On 9.44 Bolt Pattern Available On Hub and Drum?
- Shop: Dexstar Vintage Steel Wheel w/ +5 mm Offset - 13" x 4-1/2" Rim - 4 on 9.44 - Silver
- Shop: Dexter Trailer Axle w/ Electric Brakes - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Shop: Trailer Axle w/ Electric Brakes - Easy Grease - 6 on 5-1/2 Bolt Pattern - 89" Long - 5,200 lbs
- Q&A: How to Determine Hanger Spacing for Tandem Axle Trailer Suspension with 26 Inch Springs
- Shop: Tandem-Axle Trailer Hanger Kit for Double-Eye Springs - 2-1/2" Front/Rear, 4-1/4" Center
- Search Results: rv steps
- Q&A: Recommended Replacement Vintage Wheels for a 1973 Holiday Rambler
- Search Results: 4 on 944 hubs
- Search Results: 7way plug
- Search Results: gen~y hitch
- Search Results: trailer hitch
- Search Results: gen~y hitch trailer hitch
- Shop: Trailer Wiring
- Q&A: Replacement Trailer Wheel for Vintage Trailer with 4 on 9.44 Bolt Pattern and 8 Inch Pilot Hole
- Q&A: Converting From 4 On 9.44 to 5 On 5 Bolt Pattern
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Brake Controller
on Trailer Hubs and Drums
