Does Valterra 3 inch Waste Valve Fit 3 inch Bristol Hub

Question

Question:

Will the 3 inch valterra waste valve fit the 3 inch Bristol hub

asked by: William W

0

Expert Reply:

The Valterra EZ Valve Electric Waste Valve System # E1003VP that you referenced is designed to fit standard RV waste setups that use 3 inch pipes like what a 3 inch Bristol hub is so yes, it would work.

expert reply by: Jameson C

0

Answer 1

Yes you are correct Valterra EZ Valve Electric Waste Valve for RV Black Water Tank part #E1003VP does come with everything you will need. The confusion came from the spigot or hub ends and which one they needed for their application in that question.…

view full answer...

Answer 2

Hey Taylor, it looks like the Valterra EZ Valve part #E1003VP that you referenced uses 16 gauge wire but since I think 14 gauge wire is easier to work with that would be what I would go with. The amperage draw of this is pretty light so you…

view full answer...

Answer 3

The difference between a hub connection and a spigot connection is that the hub is the female end and has a lip on the inside that stops the spigot (or male) end where it needs to be. I have attached some pictures to assist. With this knowledge it is…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does Valterra 3 inch Waste Valve Fit 3 inch Bristol Hub

Continue Researching