Replacement Claw Tightener for Yakima RailGrab Roof Rack Towers

Question

Question:

Looking for the black socket head cap screw called claw tightener which is about 1/4inch fine thread and approx. 3 1/2inch long. What is the part number and where can I purchase. Nothing available in hardware stores. For Yakima Railgrab tower.

asked by: Mike Y

0

Expert Reply:

It sounds like you are describing the screw that comes with the Replacement Wedge Assembly # Y8880150. The screw only comes with this kit. The only other possibility is # Y8880148 which are the adjustment knobs for RailGrab towers.

expert reply by: Michael H

0

Answer 1

We do carry replacement parts for the Yakima Railgrab foot. For the claw base and nut you would want the part #Y8880279. The medium claws are no longer available. For the claws with pin adapters you would want the part #Y8880201. For replacement…

view full answer...

Answer 2

We have the replacement screw you are looking for with the part #Y8880150 which matches up to the nut of the #Y8880279 which is M6.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Replacement Claw Tightener for Yakima RailGrab Roof Rack Towers

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching