Where Is Door Bracket Mounted When Installing Enclosed Trailer Ramp Spring CB250D96SHD
Updated 05/20/2016 | Published 05/16/2016
Question:
I need info about the rear door CB250D96SHD . where on the door do the cables attach to retract the door. I know the unit mounts on the header and my question is about where on the door, ie top, half way, bottom. Also my current door has spring on the outside and I would like to due away with them as they are worn out. The mount for the current springs are bending the door.Will this unit work to replace the current system. if not is there a upgrade hinge kit to use on my door to move to that style of helper to eliminate the old system.
asked by: Ron M
Expert Reply:
The # CB250D96SHD is designed to work with trailer ramp doors that open from the top and when fully opened create a ramp used for loading the trailer.
The brackets that are attached to the door are typically placed at the top of the door(top of door when closed). The bar that has the springs and drums attached is mounted on the header above the door in the trailer just like a garage door spring assembly.
If you are not accustomed to adjusting the springs on a system like the # CB250D96SHD it is highly recommended to have a professional familiar with systems like this to complete the job.
Product Page this Question was Asked From
Conventional Ramp Door Spring for 8' Wide Enclosed Trailer - Dual Spring - 250-lb Capacity
- Trailer Ramp Springs
- Dual Ramp Spring
- Torsion Spring
- 150 Inch Cable
- 231 - 250 lbs
- Conventional Spring
- 6 Foot Wide Trailer
- 7 Foot Wide Trailer
- 8 Foot Wide Trailer
- 94 Inch Wide Spring
- M-3 and Associates
more information >
Continue Researching
- Shop: Advent Air RV Air Conditioner System - 15,500 Btu - Air Distribution Box Controls - Non-Ducted - R32
- Search Results: drop ~ 8 inch trailer hitch ball mount
- Search Results: rv air conditioners
- Search Results: dually valve stem extenders
- Search Results: 58272
- Search Results: car ramps
- Shop: TowSmart ProClass Plug-In Trailer Connector Adapter w Wire Tester, Ergo Grip - 4-Way Flat to 7-Blade
- Shop: Curt Class III Ball Mount with 2-5/16" Ball - 2" Rise or 4" Drop - 7,500 lbs
- Search Results: stu~010
- Shop: Trailer Wiring
- Shop: Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
- Shop: Curt Ball Mount for 2" Hitches - 7" Rise, 8-1/4" Drop - 9-3/8" Long - 10,000 lbs
- Shop: Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
- Shop: Hitch Pin and Clip For 2-1/2" and 3" Hitches - 5/8" Diameter x 4" Span
- Q&A: Dimensions of Dutton-Lainson Swivel Jack Cap # DL22354
- Search Results: sway bar
- Shop: Vehicle Sway Bars
- Q&A: Best Rear Anti-Sway Bar for 2019 Ram 2500
- Video: An In-Depth Look at the Roadmaster Rear Anti-Sway Bar-RM34GR
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
on Trailer Door Parts
