Recommended Add-On Kit For Yakima HoldUp 2 Bike Rack

Question

Question:

if I have two trays that I removed from a different hold up, is this all I need to have a complete, functional extension?

asked by: Bryan

0

Expert Reply:

In order to add an extension to be able to carry an additional 2 bikes on a Yakima HoldUp bike carrier like part # Y02443, you would need a bit more than just part # Y8890279 and the wheel trays.

You would need the upright masts needed to secure the bike frame to the extension, so I recommend part # Y02446 to make sure you have all the components needed to be able to carry 2 more bikes.

expert reply by: Jeffrey L

0

Answer 1

The Replacement Hitch Bolt #Y8890200 is the correct bolt for your Yakima HoldUp Bike Rack #Y02443. We also have the Replacement Hitch Hardware #8890260 if you need to replace the insert inside the Spine #8890277.

view full answer...

Answer 2

To replace the threaded hitch pin and lock for your Yakima HoldUp, it will depend on if you have the 2" shank or if you have the 1-1/4" shank with a 2" adapter. For the 2" shank, you will need the Replacement Hitch Bolt and Clip…

view full answer...

Answer 3

Yes, I confirmed with Yakima that the expansion kit part #Y02446 does fit your earlier version of the Holdup #02433.

view full answer...

Answer 4

That's a great question. I checked with Yakima and was told that the #Y8890279 replacement spine could be used with the trays scavenged from your older HoldUp 2 bike rack to construct a 2 bike add-on for your #Y02479 HoldUp EVO bike rack. The…

view full answer...

Answer 5

Yes, you can use Replacement Mounting Hardware part #Y8880128 to secure your Hold Up Plus 2 extension #Y02446 to your existing HoldUp platform carrier.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Add-On Kit For Yakima HoldUp 2 Bike Rack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching