Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs

See what our Experts say about this etrailer Camper Jacks

• Replacement for Atwood Landing Gear on 2004 Fleetwood Wilderness 5th Wheel Trailer
  I reached out to my contact at Lippert who said that the Atwood line has been discontinued and they don't have any replacement parts for it. Since this is the case you'll need to replace your Atwood jack. Was this for the landing gear or for a stabilizer jack? If you can let me know this I can recommend a replacement for you.
  view full answer...
• Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
  view full answer...
  
• Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
  Bulldog Tandem Landing Gear Set # BD500162 is a great option for a manual set to replace the landing gear on your Keystone Laredo. I have linked a video review for you. The handle is not included so use # BD500203 to add the crank handle. For an electric set you could use # RVLG-8HDL and add motor # LC142178 and, if you don't already have one, a switch # LC145236.
  view full answer...
• 5th Wheel Landing Gear Replacement for 2011 Wildcat by Forest River Model 31TS
  You could use the Landing Gear part # RVLG-8HDL as a replacement for what you have now on our 2011 Wildcat by Forest River. This will bolt right up in place of what you have and has plenty of capacity at 8,000 lbs so it will operate easily.
  view full answer...
• Option for Upgrading Atwood Landing Gear from Manual to Electric Set
  The Atwood line of landing gear jacks has been discontinued for some time so to upgrade to an electric set you'd have to go with new landing gear like the # RVLG-8HDL and then install the motor part # LC142178 with it and you'd have a very similar setup but with a motor that will make raising and lowering the trailer easier.
  view full answer...
• Replacement Landing Gear for 1995 Sierra by Cobra
  For replacement landing gear on your 1995 Sierra by Cobra you can use the Landing Gear Set # RVLG-8HDL. Since nothing matches your weld stop measurements you will also need to weld on new brackets # LC113511. This landing gear has a capacity of 8,000 lbs and uses the standard inside 15-1/2" and outside 17-1/2" measurements found on most modern landing gear. If you want to add a motor it is available separately # LC142178.
  view full answer...
• Replacement Landing Gear For A 2008 Weekend Warrior Road Warrior 5th Wheel Toy Hauler
  Hey Bob, Landing gear components aren't all interchangeable between brands so I'd need to know the exact model to find replacement parts for your current system. If you're just wanting to replace the landing gear as a whole then I'll need to know the the spacing for the weld stops. For example, the Landing Gear Set w/ Handle # RVLG-8HDL you were looking at has a 15-1/2" inside and 17-1/2" outside measurement, which is a pretty common spacing. If your spacing differs then you'll have...
  view full answer...
  
• Replacement for Atwood MPD 71125 5th Wheel Landing on 5th Wheel Camper
  Since Atwood is no longer in the landing gear business it is basically impossible (unfortunately) to get just a replacement leg. The part number that you gave me actually is a document that shows the various parts for Atwood landing gear, but nobody has information as to what those replacement parts are the equivalent of. Because of this I recommend replacing the landing gear on your 5th wheel trailer. This gives you some peace of mind that you won't have to replace any parts in the near...
  view full answer...
• Recommended Replacement Landing Gear Set for a 2004 Keystone Cougar 5th Wheel Trailer
  When you are looking for replacement landing gear the 2 big things to take into consideration are the weight of your trailer and the weld stop locations on your current setup. Since the GVWR of your 2004 Cougar is 10,300 lbs our Landing Gear Set w/ Handle # RVLG-8HDL that you referenced can handle the weight capacity of your RV. Keep in mind that some of the weight of your trailer is still supported by the axles and tires so a landing gear setup doesn't need to be rated for the total GVWR...
  view full answer...
  
• Replacement Landing Gear for 2009 Heartland Sundance 5th Wheel Trailer
  The 8K Landing Gear Set w/ Handle # RVLG-8HDL should fit just fine as it uses the standard weld stop locations measuring 15-1/2" or 17-1/2" for the mounting brackets. I don't know what the current bracket dimensions are for your 2009 Heartland Sundance but you can quickly verify if this is compatible by measuring the space between your mounting brackets. If it is 15-1/2" or 17-1/2" then you are good to go! This landing gear comes with a manual hand crank and you have the option to add...
  view full answer...
• Motor for etrailer Landing Gear Set w/ Handle
  Hi Bob; are you referring to the Landing Gear Set w/ Handle # RVLG-8HDL you purchased a little over a year ago? If so, the correct motor is the Lippert Venture 5th Wheel RV Landing Gear Motor # LC142178. If you were looking for something else please let me know in the comments below.
  view full answer...
• Distance From Top of Weld Stop to Crank Shaft for the etrailer Landing Gear Set
  Hey Chad, From the top weld to the middle of the crank shaft is 6" for the Landing Gear Set # RVLG-8HDL. If you were talking about the rod at the top of the gearbox then that would be 8-1/2". Attached are some dimensional photos for you to check out.
  view full answer...
• Dimensions of etrailer Brand RVLG-8HDL and RVLG-8000 Replacement 5th Wheel Landing Gear
  The only difference between the # RVLG-8HDL and the # RVLG-8000 is that the # RVLG-8HDL includes the manual crank handle, while the # RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of 53-1/4 inches The tabs for the mounting straps measure 17-1/2 inches from the top of the top most tab to the underside of the lower tab. From the underside of the top tab to the top of the lower tab is 15-1/2 inches. I've shown these dimensions...
  view full answer...
  
• Can The Gearbox For The etrailer Landing Gear Set Be Mounted Horizontally
  The gearbox # RVLG-RDBOX for the Landing Gear Set w/ Handle # RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place match up perfectly for both positions (pictured below).
  view full answer...
  
• What Is The Difference Between The Landing Gear Set RVLG-8000 & RVLG-8HDL?
  The only difference between the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-8HDL that you mentioned, and the Landing Gear Set # RVLG-8000 is that # RVLG-8HDL comes with the handle, whereas if you were to go with # RVLG-8000 you'd need to purchase the handle separate with # RVLG-HDL. Both of these systems are rated for the same 8,000lbs capacity limit, and have 36-1/2" of total lift. Additionally, both of these can also be upgraded from manual to electric...
  view full answer...
• Difference Between 8,000 lb Landing Gear RVLG-8HDL & RVLG-8000
  The only difference between these two 8,000 lb landing gear sets - other than price - is that one comes with the crank handle and the other does not come with the handle. - Comes With Crank Handle: Landing Gear Set w/ Handle # RVLG-8HDL - Comes Without Crank Handle: Landing Gear Set # RVLG-8000 Apart from that, these are 100 percent the same landing gear.
  view full answer...
• Landing Gear Kit For A 2010 Keystone Montana Hickory
  When it comes to adding a landing gear set to your 2010 Keystone Montana Hickory The Landing Gear Set w/ Handle # RVLG-8HDL will work for you. The landing gears have a durable, black powder coated outer tube and has zinc-finished inner tubes that provide excellent corrosion resistance. The kit comes with a manual crank but you can purchase the 12V DC motor # LC142178 separately. The landing gear kit has a combined weight capacity of 8,000 pounds. The lead leg of your landing gear is...
  view full answer...
• Determining The Correct Replacement landing Gear Set For A 1995 Fleetwood Terry 5th Wheel Trailer
  To determine the correct replacement landing gears for your 1995 Fleetwood Terry you'll want to measure the inside to inside and outside to outside measurement of the weld stops on your current landing gear set so we can see if there's a match that can just reuse your current mounting brackets. If there isn't you would have to cut off he current brackets and have a qualified welder weld on new brackets, which can drastically increase the cost. The standard for most landing gear sets is...
  view full answer...
• Mounting Brackets to Use with Landing Gear Set # RVLG-8000
  Hey Ronald, the landing gear part # RVLG-8HDL does not come with new brackets but we have them available with the part # LG-Brackets. These will need to be welded on as there isn't a way to bolt on the jacks to the brackets you have now.
  view full answer...
• What Lead Leg for Landing Gear Will Fit the Stromberg Carlson Electric Landing Gear Motor LG-142178
  The Replacement Motor for Stromberg Carlson Electric Landing Gear # LG-142178 will work with Stromberg Carlson model(s) LG-1 or LG-2 and most electric landing gear sets, including Atwood, Venture, and Lippert models. You don't really pair the lead leg to the motor, you would find a motor that is compatible with your landing gear/lead leg. If you have one of the systems above, you would be good to go with the # LG-142178. If you are needing a lead leg that is compatible with a motor and...
  view full answer...
• Inexpensive Landing Gear For Keystone 5th Wheel Trailer
  Hi AJ, I can give you some help on selecting the right landing gear, though it is a universal type of fit, and there isn't landing gear specific to any trailer. That said, it's pretty easy to determine, as all you will need to do is measure the distance between the mounting brackets on your trailer as shown in the diagram below. From there you will be able to choose the amount of lift and that will work for you. For example, if you have the standard dimensions between your brackets (which...
  view full answer...
• Would etrailer.com Landing Gear Set # RVLG-8HDL Fit 1996 Excel 5th Wheel Camper
  The Landing Gear Set w/ Handle # RVLG-8HDL that you referenced is MOST LIKELY the correct set of landing gear for your 1996 Excel 5th wheel camper as this landing gear fit is the most common seen on RVs. I would actually be shocked if it didn't fit because of that. So what you'll need to do to verify is measure the dimensions of the welded mounting brackets on your camper and compare them to the picture I attached. The sure way to tell is that if the distance between the mounting brackets...
  view full answer...
  
• Will etrailer Landing Gear RVLG-8HDL Fit 2003 Keystone Cougar 276EFS
  The landing gear kit part # RVLG-8HDL will bolt right up in place of the landing gear you have installed currently on your 2003 Keystone Cougar 276EFS but the motor kit won't work since your old setup was a Fulton. What you'd need to add a motor to this is the part # LC142178. The distance from the top of the upper weld mount to the center of the manual crank shaft is 10 inches.
  view full answer...
• How to Choose Replacement Landing Gear for 5th Wheel Trailer
  The first thing you want to do before you find a replacement is to check the rating on your current landing gear. You want the new landing gear to be rated for at least the same amount. You will also need to measure the weld stops to make sure they match up so you won't have to do any welding. For example, the Landing Gear Set w/ Handle # RVLG-8HDL you were looking at is rated for 8,000 lbs. The distance from the top of upper weld stop to bottom of lower weld stop is 17-1/2" which is the...
  view full answer...
  

Do you have a question about this Camper Jack?