To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded trailer hitch receiver bolts onto your Ford 's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Tech Tip
Spare tire may need to be repositioned. Drilling required for installation , Does not fit models with rollpan bumper , Spare tire will need to be lowered or removed temporarily for hitch installation , Does not fit Cab and Chassis or vehicles with 34 inch frame
Complete Towing Package for 1991
Customers compare 14001 to these similar products
1991 Ford F-150, F-250, F-350 Owners Who Purchased This Trailer Hitch Also Bought...
Popular Trailer Hitch Accessories
Average Customer Rating: 4.8 out of 5 stars (246 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.Hangs down a bit low on my 79 150, but its a clean look. Easy to install, but I'd recommend a stepped drill bit to make the install possible with a 3/8 drill. Top of the receiver is 3 1/2" below the stock bumper.
The packaging was solid and so was the fast delivery. Good fit only a couple of modifications to miss one of the factory rivets. Pushed to one side Against the leave spring bracket the hole used to miss the rivet fell in line with the rolled ninty of the hitch. A grinder and cutoff wheel did the trick. I would have to drop my gas tank down out of the way if I want to through bolt the rest of the hitch plate. The edge of the tank is in line and next to the frame. I'm thinking on drilling and taping and using some lock tight and call it good. It was fairly easy to install once you tie one end up and then hold the other end and mark your holes with a sharper. Through bolt the side you just drilled and then repeat. Very well fabricated I would recommend this style of hitch to anyone.
Installed on a 1973 Ford F-250 with 37-3/4" frame. Installation was straight forward. Product fit well. I put the second hole on the last riveted frame cross member, everything lined up perfectly. Make sure to allow enough room for the washers on top of the frame rail, I had to use a die grinder to open up one hole because I made the hole too close to the frame and could not get the washer to sit on the frame rail. A second person and C - Clamps helped a lot. We lifted the receiver into position, clamped it in place. I drilled one hole on each side, installed the bolts, then removed the clamps and drilled/installed the rest of the hardware. Contrary to the instructions, I did not have to remove my spare tire (thank Jesus!).
Great product, shipped fast. This is my third Curt hitch and one of many times I've used etrailer.
This hitch appears very well make and was fairly easy to install on my Bronco. Even at 70 I had no issues and it took about an hour at a slow pace. First thing I did was wire it to a floor jack and jack it in place to mark the holes, step drilled as recommended and fished the bolts through as is necessary on the Bronco due to the fuel tank position. I didn't see any Bronco install pic here so here are a couple of pics. Very similar to the F150 type install except for the fuel tank.
Tony
7/6/2022
Still secure and working exceptionally well.
Excellent customer service! Well made product, fair price.
Highly recommend.
The product was an easy install just as they said. The wiring was also simple to install. It works perfectly and also increases the value of my truck because it’s equipped to haul trailers or campers with an taillight / brake lights hook up.
I was very impressed with this and will definitely contact etrailer again if I need anything else.
I'm 75 years old and not getting around like I used to. The Curt class IV hitch aligned perfectly with frame existing holes. Center hole needed to be drilled, easy enough to do. The existing 3500 lb.bumper hitch was removed. Some wiring was attached to frame and needed to be relocated. My son stopped by to help with installation, but we found a floor jack could be used to position hitch without need for extra muscle. Once lifted, we used clamps to hold in place for hole enlargement and drilling. Looks like it will tow much more than truck is certified to pull
Fit my 1977 Ford F250 Super Cab Camper Special with step bumper. The guide holes fit right over the rivets on the frame rails. Leaves adequate room for my spare tire to continue to be carried by the undermount system. Just what I was looking for. Still mulling over where and how to place my trailer wiring receptacle. Might put a six-pin round in the left license plate light hole.
Product quality is exactly like every other Curt part, no problems. Packaging and shipping from etrailer was lacking. Albeit quick, but the product was outside the box on my doorstep. Hitches get beat up and rusty over time so not worth complaining, but still a bit disappointing.
I ordered the Curt Trailer Hitch Receiver on the Memorial Day weekend and it was delivered on Friday, the same week. I found the Curt Trailer Hitch Receiver fit my 1980 Ford F150 Pickup without any problems. Other places I checked did not have Trailer Hitch Receivers for vehicles this old. It took a little over an hour to install. The extra time was needed to drill six 1/2" holes in the bottom flange of my truck frame.
It was indeed a perfect match to my F-350's rear end. It tows large trailers well, and as of last month, survived a rear-end colission "without a hitch," pardon the pun. It is still perfectly straight. Good product!
Product arrived earlier than expected and install instructions were perfect. Great. Alue
This hitch was the perfect replacement for my truck, Great product and service ,the price was very fair. I received my new hitch and had it back on the truck in a day, would recommend etrailer to everyone and will use again if needed in the future.....
The hitch arrived in 3 days in great condition. Good packaging. My installation took a little longer than most I am sure. My bumper mounts have a "C" shaped cross section that covered the areas on both sides of the frame where toe rear most bolts needed to be installed. Had to remove the bumper.
I have purchased several items from ETrailer over the years. All have been high quality and the prices can't be beat.
I will always dream with etrailer when I need towing components.
Fits perfect on my 1999 Dodge Ram 1500 and easy to install.
2nd curt hitch I've installed, had it done in 35 minutes. Didn't have to move the spare or rear bumper. Really easy install. Good shopping by etrailer too.
Fitment wasnt perfect it was a little narrow for my frame but still bolted up and has hauled good, no problems, was put in a 1995 f150 4.9 rwd 5 speed single cab long bed
Installed Curt hitch class 4 2” and after a year here in Mn still has a gloss finish on black paint. Well made and installed fairly easily and had all hardware required.
awesome hitch,super easy install,great price.have worked great for towing my car trailer.curt hitchs are the best.
Scott E.
2/26/2023
this hitch is still awesome.would recommend to anyone who needs a quailty hitch.
Great service and quick shipping.
I am Soo happy with how easy this hitch receiver was to install. Everything fit perfectly and was well packaged.
Arrived on time. Perfect fit. No issues. Will definitely order from you guys again.
Cesar F.
10/18/2018
Works great
item looks great . It will be quite some time before I will be able to get it installed .First off the truck has a home made hitch welded on it now . I will have to get it off first . My shop is working outside and with winter coming it will take time . I'll try and send you some pictures of the one I have to cut off , And in time send you one with it installed on truck .
Regards
William
12/1/2022
Dont know yet . I have had a few health issues last year . The hitch looks great and in my mind Im sure it will work as it should . Number one is the person that owned the 1985 Ford F350 dually had someone weld a make shift hitch on it , and I will have to grind it off to put this nice hitch on .
Good quality hitch. Fits as it should. Sits low on my lowered truck but does the job.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Ben
2/16/2021
After a year and several 10,000 tows. Still going strong and the finish is holding up nicely.