trailer tool box

Hey Sean, From the bottom of the etrailer Trailer Tool Box #e44VV to the bottom of the gas strut bracket is right at 19". There's also the latching mechanism on the front of the box that sticks out inside the box that that's about…

Hello Jim, thanks for reaching out. We do have a hitch mounted carrier that works great for mobility scooters. Take a look at the Erickson Aluminum Mobility / Cargo Carrier #EM34JV. This is made of aluminum so it is strong and lightweight. It has a…

Hey Tom, yes the Erickson Cargo Carrier part #EM34JV would work great for you as it has the needed clearance to fit past the rear of your RV as well as has the needed weight capacity.

Hey Linda, thanks for reaching out! Yes, the Erickson Aluminum Mobility / Cargo Carrier #EM34JV uses an M16 threaded bolt for the hitch pin. Are you looking to replace it, or are you trying to get on in advance? (This already comes with one)

Hey Keethe, I can clarify that for you! The etrailer Trailer Tongue Tool Box - A-Frame - Aluminum - 6 Cu Ft #e44VV is much more affordable, but certainly not lower quality than the similar options like UWS A-Frame Trailer Toolbox - 6.3 cu ft…

We have one aluminum folding option for you and it is the 19x60 Curt Cargo Carrier for 2" Hitches - 500 lbs #C18100. This carrier is well made and will store close to your vehicle when not in use. We have another aluminum option also rated for…

We have seen people mount storage boxes on either side of the nose of a V-nose trailer like what you see in the picture I attached. The part #DZ91717P would work well if you have room for it like that. The dimensions of the box are 36" long…

These toolboxes do not contain mounting hardware due to the different construction and mounting locations that may be required for many different styles of trailers. A lot of how you install the UWS A-Frame Trailer Toolbox #UWS01065 depends on where…

Hey Frank, the cross section depth of a frame is the width of the frame's channel. So the etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks #e52JR can fit on frame channels that are less than 3 inches in width which is due to the…

Hey Frank, on the etrailer box part #e64VV all of the walls are welded. The thickness of the steel is 13 gauge. What will you put in the box?

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

Hey Frank, the radius for the handle of the etrailer jack part #e22ZV is 8-1/8 inches. That means it sticks out 8-1/8 inches from where it attaches to the jack. From the center of the jack mount to the top of the jack measures 7.5 inches.

Hey Sean, From the bottom of the etrailer Trailer Tool Box #e44VV to the bottom of the gas strut bracket is right at 19". There's also the latching mechanism on the front of the box that sticks out inside the box that that's about…

Hello Jim, thanks for reaching out. We do have a hitch mounted carrier that works great for mobility scooters. Take a look at the Erickson Aluminum Mobility / Cargo Carrier #EM34JV. This is made of aluminum so it is strong and lightweight. It has a…

Hey Tom, yes the Erickson Cargo Carrier part #EM34JV would work great for you as it has the needed clearance to fit past the rear of your RV as well as has the needed weight capacity.

Hey Linda, thanks for reaching out! Yes, the Erickson Aluminum Mobility / Cargo Carrier #EM34JV uses an M16 threaded bolt for the hitch pin. Are you looking to replace it, or are you trying to get on in advance? (This already comes with one)

Hey Keethe, I can clarify that for you! The etrailer Trailer Tongue Tool Box - A-Frame - Aluminum - 6 Cu Ft #e44VV is much more affordable, but certainly not lower quality than the similar options like UWS A-Frame Trailer Toolbox - 6.3 cu ft…

We have one aluminum folding option for you and it is the 19x60 Curt Cargo Carrier for 2" Hitches - 500 lbs #C18100. This carrier is well made and will store close to your vehicle when not in use. We have another aluminum option also rated for…

We have seen people mount storage boxes on either side of the nose of a V-nose trailer like what you see in the picture I attached. The part #DZ91717P would work well if you have room for it like that. The dimensions of the box are 36" long…

These toolboxes do not contain mounting hardware due to the different construction and mounting locations that may be required for many different styles of trailers. A lot of how you install the UWS A-Frame Trailer Toolbox #UWS01065 depends on where…

Hey Frank, the cross section depth of a frame is the width of the frame's channel. So the etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks #e52JR can fit on frame channels that are less than 3 inches in width which is due to the…

Hey Frank, on the etrailer box part #e64VV all of the walls are welded. The thickness of the steel is 13 gauge. What will you put in the box?

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

Hey Frank, the radius for the handle of the etrailer jack part #e22ZV is 8-1/8 inches. That means it sticks out 8-1/8 inches from where it attaches to the jack. From the center of the jack mount to the top of the jack measures 7.5 inches.