Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…
Thanks for reaching out Greg, we get this question from time to time. At this time, we don’t offer any tire and wheel packages in a 5 on 4.25" bolt pattern. The main reason is this bolt pattern's typically is found on a passenger vehicle…
Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…
Jason, you only need one Hub Saver per wheel. Since they're sold in a pack of two, one package is enough for a single-axle trailer with two hubs. If you have a tandem-axle trailer, you'll need two packs to cover all four wheels. The Hub Saver…
Hey Michael, yes the hitches from the 2025 Sprinter fits also fit the 2026 models like the etrailer #e82TR. We haven't carried them over quite yet in our fitguide but we will be soon. What are you planning on using the hitch for?
Hey Jeff, Depending on how much clearance you need from that tailgate is going to determine what kind of hitch extender you will need. Assuming you just have a factory 2" hitch receiver on your Ram you could go with the hitch extender #e48YR…
Hey, Lance. The direction the springs are in doesn't matter. They can be to the front or to the rear of the axle and will perform the same either way. What kind of trailer are you working on?
Hi Richard; we have no way of knowing what mounting bracket/brakes are on your Load Rite trailer. If you have Dexter/Tie Down Engineering disc brakes with a 9.6" rotor there is a good chance the #DX89UR will fit. However, it is probably best to…
The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…
Hey Dale, do you happen to know axle capacity you need? That's a very popular leaf spring length that we have springs for axles that range from 3k to 7k. Most popular is 3,500 lb axle like the part #DX23CR but I attached a link to all of the…
The Kodiak #20TA-BLKIT 20 foot brake line kit will work if the distance from the rear of the coupler to the front trailer axle is roughly 18 to 19 feet, as you'll need some slack for the swing-away coupler to move freely. having a little extra…
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA
Boat Motor Accessories with transom support plate
Install is straightforward with boat motor accessories that include a transom support plate, so they fit right with no adjustment needed and look great. They work great and do what they are intended to do.
Often they fit with no adjustment when the hole spacing matches. Verify the center-to-center on the holes before you start. Dry-fit the plate to confirm alignment. If hardware resists threading, stop and recheck spacing rather than forcing it.
Match the plate's mounting hole pattern to your transom or motor bracket. Measure the center-to-center distance on your setup and compare to the plate spec. Check overall plate size so no trimming is needed. If your hardware lines up, installation is straightforward.
Confirm the center-to-center hole distance matches your transom or bracket. Measure both horizontally and vertically if the pattern is slotted or multi-hole. Compare your measurement to the plate's published spacing. A proper match helps avoid modification.
A clean, well-matched plate can look great once installed. Choose a finish that suits your transom and keep edges aligned for a tidy appearance. Test fit to ensure it sits flat and even. Tighten hardware evenly to keep the plate flush.
Filters
