To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This proportional brake controller has simple controls and a digital display for diagnostic information. Includes 3 boost levels, a slide-bar manual override, built-in battery protection, automatic leveling, and continuous diagnostics.
Features:
[PHO]Tekonsha Primus IQ Brake Controller- Proportional -1-3:Specs:
[PHO]Tekonsha Primus IQ Brake Controller- Proportional -1-3:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there hollers there. Today we're going to be taking a look at Tekonsha's Primus IQ proportional trailer brake controller.This brake controller is going to be your entry level into a proportional brake controller and even though this is entry into proportional, I would recommend it over most of your time delay modules, just to how much smoother your breaking experience is going to be with a proportional controller, because proportional means that it uses an internal inertia sensor to detect the movement of the vehicle.So as we hit the brakes and go to a stop, that inertia sensor is going to detect that loss of motion and it's then going to use that information to apply a signal to the trailer brakes at the back, which will apply them. But it uses this information to help match the application of the brakes, to what you're doing here in the vehicle. So that way, when you hit the brakes, you're going to get a softer brake application at the trailer if you hit the brake softly in the vehicle. And then if you need an aggressive stop, like an emergency stop and you hit the brakes hard here in the vehicle, it's then going to detect that quick stop and it's going to put out a hard, aggressive brake to your trailer.With your time delays, you're just going to have whatever you have your setting to on your adjustment. And then a few seconds after applying the pedal, it will then apply to that exact amount that you've got it set to.
And that can be useful if you do a lot of off roading because you just want your brakes to apply. But for most people that are just going to be driving out on the roads, hauling going from campsite to campsite, proportional is going to be significantly smoother and a much more enjoyable experience.For example, when using a time delay brake controller with our boat here, if we come into an emergency situation or we're getting off the highway and we need to hit the brakes to come to a stop, with that time delay, we've got them set aggressive so that way we can get the application we need so this boat's not pushing us up that off-ramp. But when we're just breaking around town, going through stoplights and just here in the city, every time we hit the brakes, that brake controller applies with that same pressure and it's too much. We feel the trailer wanting to stop us before we get to the stop that we wanted to come to at the stoplight. So then we have to adjust our time delay brake controller down and up to meet those various situations so it feels properly when driving.
With our proportional controller in here, once we set the adjustment for the application, at that point, when we go into those different situations, the controller's going to take over and do all of those adjustments for us. So it just feels smooth the entire time.Our initial adjustment we're making is just for the particular size of the trailer that we're currently hauling. And with our boat here, we are getting pretty close to the weight of our Sorento. So we are going to be using the boost two setting with it to give us a little bit more aggressive braking to match this.Now we're just talking about the boost setting on our brake controller and it has three different boost options, as well as being able to turn the boost completely off. The boost is just going to give it a more aggressive strategy when using that inertia sensor information to be more aggressive.
And that's important when you've got extremely heavy things, you need that more aggressive braking. So when we got our John boat here hooked up, we're likely going to have it in the boost one, or maybe even the boost offsetting depending on how it feels, because this is significantly lighter than what our vehicle is.And for you people at home hauling a camper that is likely heavier than your vehicle, you'll want to use that boost three setting to get that more aggressive braking so this isn't pushing you when you're coming to a stop off the highway. Now, regardless if you're in the boost one, two, three or you have the boost turned off, your power adjustment is going to play a factor into how hard that applies. I'm going to hit the manual slider all the way over so you can see our maximum output. And as we adjust this, it does dial back what our maximum is going to be.
So if we have it on that boost three setting, it's going to apply more aggressively, but it's not going to apply harder than where we've got our power output set to here. So that way you can set that maximum and that can be really useful when you've got a medium or smaller trailer. Maybe you don't ever want this inertia sensor to put it at that maximum output. You can dial that back with the setting.Now, if you're using those boost settings, like when we we're backing our boat up here, it does make it more aggressive. And when you're backing up that inertia sensor might be applying a little bit too early, because when you're backing up, you're doing things slow and you're doing a lot of turning and a lot of tapping on the brake to get that position you need to, so you can get it into that spot. And that might be applying your brake controller's brakes here on your trailer, causing it to stop. And then all of a sudden you're backing into your trailer. Well, there's a reverse mode setting that we can temporarily apply for when backing up. So that way our boost isn't being too sensitive and applying those things.To put it into that reverse mode and temporarily cancel out the boost, you'll just want to hold onto your brake pedal. Just press down on that and then press down on the boost button and after a few seconds, you'll see, it will have a flashing R indicating that you're in the reverse mode. And now you don't have to worry about those brakes applying when you're backing up. And like most of your traditional brake controllers, there is a manual slide on it so you can manually apply the brakes on your trailer, if you need to.This can be useful for testing purposes. If you're just wanting to test the output, test the proper operation of your brakes, you can manually apply it with this. And it's also useful if your trailer starts to sway behind you, because that swaying motion when it starts going on, can potentially cause issues with stability and driving the vehicle. To straighten that out, we can hit our manual slide a little bit and that's going to apply the brakes in our trailer. So instead of being able to sway, our vehicle now wants to leave the trailer because the trailer is applying the brakes. That's going to pull them taut, and it's going to bring that trailer straight in line behind your vehicle once again.When your trailer is disconnected, you will see an NC located here on the screen. We just disconnected it right now and it does this so that, you know, hey, if you are driving, you have just been disconnected. You're no longer applying a brake signal to your trailer. It lost that input. And if you don't have anything connected, you're in your vehicle right now. You can be sure that you're not connected. You hit your slider here, it'll say NC. This can also be useful if you plug in your trailer and it doesn't seem like it's functioning, you should not see NC when your trailer's plugged up. That means that it's not currently detecting that there is a trailer plugged in and then you can correct any faults you've got with the wiring on your trailer, test it back out and ensure that you don't see the NC when you're hooked up.The two digit display will display your power output. And it also constantly monitors for any faults. And you can get fault codes on here. So you can use the troubleshooting in your instructions to help determine where the fault is and what's causing it.You'll have two different mounting options that come included with your brake controller. You've got the snap in mounting option, which is my preferred option because it's a little bit more low profile. It keeps itself closer to the dash and it only requires the two screws and you can easily click the module in and out with this bracket. It simply slides in the bottom there. And then it clicks up into place.And with our other bracket here, it does have adjustments. So if you can't achieve the appropriate angle with this bracket, you may need to use this one, but this can be mounted in a positive 90 degree to negative 90 degree orientation. So currently we're at zero that all the way straight up would be positive and all the way straight down would be negative 90 degrees. So you get a lot of options on how you're going to mount it. As long as you mount it level this direction, it can be again, tilted up or down, front to back. This other option here, you can see it has a slot on it. So you can mount it up using two screws here, wherever you want to position it. And with the slotted hole here, it will bolt to the side and then you actually get a tilt. So you can change that adjustment if you need it. In most cases, though, I feel like this is the best bracket for most vehicles.Now, when it comes to the installation of your brake controller, that's going to vary quite a bit, depending upon your vehicle. If you've got a truck, in most cases, they are already pre-wired underneath the dash and you can get a custom fit wire adapter here at etrailer.com, that will go from our Tekonsha brake controller and plug directly into the factory connector and then you're good to go. You'll want to use our fit guide to determine if there is a factory connector available for your particular vehicle.Now, something like our Kia here, your smaller SUVs or regular cars, those ones are likely not going to have a factory option. We have kits available though. Kit ETBC7 is going to provide you with your seven way connector as well as the wiring to get it hooked up for your brake controller.In addition to ETBC7, if you don't have a fully functioning four way connector, you'll need that as well because ETBC7 provides you with the wiring and seven way that you need for your brake controller, but does not provide you with the wiring for your lighting functions. But we have custom fit wiring options here at etrailer.com that have plug and play connectors for most vehicles. So you can simply just plug those in line and get a functioning four pole at the back, which provides you with all of your lighting signals. That'll just plug into ETBC7 here and then you can finish installing the rest of the kit to turn that four pole into a fully functioning seven way that can work with your brake controller.Now, if you've got multiple trailers you want to haul, then instead of going with the entry level proportional that the Primus IQ provides, I would recommend to Tekonsha's Prodigy P3. This will allow you to set trailer profiles. So if you've got a small trailer and a medium and a large sized trailer, or maybe two different large ones, maybe one's electric over hydraulic, you can make those adjustments and save those profiles. So that way you can just choose that profile when you hook up and it's already got your settings saved and you're ready to go.If you have limited space under your dash for a brake controller, there are brake controllers that can actually mount at the back and plug directly into the seven way connector like Curt's Echo. That's definitely one of the best options for that limited space there in the front. I'm a pretty tall guy and it really bothers me when I'm driving and my knee keeps hitting on my brake controller. So that's one of my favorite ones out there since I can get that out of the way and put it at the back of the vehicle.And that completes our look at Tekonsha's Primus IQ proportional brake controller.
Ratings & Reviews
Patrick B.
1/30/2014
Just a quick note, there is an automatic shut-off on the Primus IQ. After 15 minutes or so of in activity, the controller will power down automatically. As soon as the controller detects movement, it comes back on. No battery drain, and you do not have to remember to turn the controller off or on.
Les H.
8/9/2015
what year Tundra in pics . I have a 08 and I am going to get an IQ for it . do you still like yours ? i guess a ground is needed ? I see what looks like a one white wire with harness
Steve M.
12/27/2017
After a year of use I am very impressed with this controller. Previous controllers I have used tend to be too aggressive on applying the trailer brakes, especially in stop and go driving, but not this unit, it is very smooth. However, when needed, as in one emergency stop last year it pulled us up quickly and straight. I would certainly recommend this product.
V J.
10/2/2016
Brakes work perfectly. Our rental trailer worked out great for an 800 mile round trip and 4 nights at a Florida State Park. We bought a used 20 travel trailer in February and have taken it on two short trips and a month long vacation. We have had no problems at all and now have almost 3000 miles of towing behind us. One emergency stop was exciting, but the rig stayed perfectly straight and probably stopped shorter than the Blazer would have done without the 4 extra brakes behind it. Thanks for all of your help and support.
Alan
1/18/2018
flawless
Terry G.
8/21/2019
Still working great
Don F.
12/29/2017
Still works great, quality product=Happy Customer!
Mike L.
2/18/2026
Glad to hear you like it! The Primus is an excellent no-frills option.
Do you have a question about this Trailer Brake Controller?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
J
12/19/2014
Thanks Patrick for the follow-up. The brake controller, for the camp trailer, installation went relatively easy and operation of the unit continues to be great. More importantly is your product follow-up for Customer Service...providing a r-e-a-l name vs. Customer Service dept. along with a phone number and email contact information all pretty rare in todays environment. E-Trailer continues to be my first-source for product information search.