Attaching Brake Controller Install Harness 7865 to Tekonsha Voyager

Question

Question:

Want to install a Tekonsha Voyager controller on my 2019 RAV4. Tekonsha PN 7865 is necessary because of the diode in the red wire to prevent backfeed of power from the brake light switch. Unfortunately, my controller lacks the plug female to accept the Tekonsha 7865 it was hard wired previously. Searched Tekonsha and your sites for the female plug end without success. Can you provide the proper female plug end to accept the male plug end on the Tekonsha PN7865?

asked by: Mark A

0

Expert Reply:

You'd just have to cut the connector your Voyager has now off so that you can hardwire the # 7865 to it matching color for color since yours was already cut and wired. We don't have a harness that fits to factory wiring of your vehicle.

expert reply by: Jameson C

0

Answer 1

The TorkLift GlowStep Revolution Scissor Steps part #TLA8002 would be a perfect upgrade option for your Jayco Jay Flight Swift SLX 154BH. The steps are designed for a 27-1/2" mounting bracket width which should make for a bolt-on swap. They are…

view full answer...

Answer 2

Yes, you will likely see the issue of the malfunctioning Pre-Collision System (PCS) on your 2018 Toyota Highlander with the Tekonsha Primus IQ Trailer Brake Controller #TK90160. So you can do is the Roadmaster Single Park Light Diode #RM-690.

view full answer...

Answer 3

We currently do not have any installation videos for the Redarc Encapsulated Power Diode #RED34FR being used to install the Redarc Tow-Pro Liberty Brake Controller #RED24FR with the Harness #RED69FR and Panel #RED48FR for any vehicles or your 2021…

view full answer...

Answer 4

On your 2019 Toyota Highlander Hybrid, you do not disconnect the brake light switch. On Hybrids unless the battery is disconnected or ignition is in the off position you may set off a code in the computer system that limits the vehicle's motion.…

view full answer...

Answer 5

Yes you need the diode arrow to point towards the brake controller. That will allow the voltage to travel into the controller but not backfeed back on to the Highlander in any way. If you need a diode we have the part #RM-690.

view full answer...

Answer 6

We have just what you need to tow your camper with your new 2017 Toyota Highlander. First, if your Coleman Popup Camper does not have electric brakes and you are only needing to power its rear signal lights, I recommend installing the Tow Ready…

view full answer...

Answer 7

As you said, we typically recommend grounding directly to the vehicle battery when doing a hardwire install using the #ETBC7 install kit. From what I understand, the suggestion for using a chassis ground is mainly meant for vehicles with CAN bus…

view full answer...

Answer 8

When mounting 7-way brackets you actually don't want to attach to the frame of the hitch by drilling into it. The best place to attach the bracket of the #ETBC7 that holds the 7-way should be on the bottom of the rear bumper.

view full answer...

Answer 9

Since you said you do not have a towing package on your 2015 Highlander, you will first need to start with a 4-way wiring harness like part #118449. This harness simply plugs into the connection points located in the rear cargo area as shown in the…

view full answer...

Answer 10

Hey Dave, yes the Timken grease seal part #TMK58ZR is a replacement for what you have now. I would go with the Timken but we also do carry your exact part number replacement with the part #58846.

view full answer...

Answer 11

Yes, the Tekonsha OEM Replacement Vehicle Wiring Harness item #22119 will fit your 2019 Toyota Highlander. This will provide you with a 7-Way connector and a Tekonsha brake controller adapter. This wiring harness is custom fit and plugs directly into…

view full answer...

Answer 12

The Tekonsha Prodigy P3 #90195 and the Curt Echo Mobile Trailer Brake Controller #C51180 do not require the stop light switch. While these brake controllers do not require the stop light switch most proportional controllers like the Prodigy P3 #90195…

view full answer...

Attaching Brake Controller Install Harness 7865 to Tekonsha Voyager

Continue Researching