Great upgrade when pulling our 6500lb travel trailer. Helps with sag and control on the road on our Ram 1500. Change the stock shocks and if you choose, upgrade your stock springs, and you'll get the most out of your half ton.3267662

Click to Enlarge

Added these to my F250 Super Duty. I carry a golf cart on a Diamond back bed cover. Can be a little top heavy. Perfect addition to my suspension- greatly reduced the sway.3537489

Click to Enlarge

1.5" gap... it came with 1 spacer for each side. if i buy the spacer kit, what size are they ? i have a 2026 f350.3616024

Click to Enlarge

Helps prevent about 1/2" of sag with my 175lb-tongue weight trailer and easy to install.3615575

Click to Enlarge

Easy to install using basic hand tools, and stopped the "sag" when I hook up my Casita travel trailer3579784

Click to Enlarge

Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!1639409

Click to Enlarge

Click to Enlarge

Click to Enlarge

Great product. The ride and body roll at the rear axle are notceably improved (1989 Ford E350 Class C RV , 27 ft). I give it 4 stars because the installation was slightly complicated due to the rear brake lines needing to be slightly bent to provide clearance for the U bolts supplied in the kit. Great product and wish it came in a 5000 lb version.3523995

Click to Enlarge

2,000 miles in on a trip from the east coast to the Canadian Rockies these work great while loaded and towing. Close to zero bounce while towing, I love them. Unloaded, however, the ride in my 2026 Tundra has gone south. There is a noticeable, abrupt stop of the units hitting the axle when going over any kind of bump. When I get home and back to regular driving, I may just take them off, its that bad.3587319

Click to Enlarge

I've had these on our tow rig for a year now and I added buy them again today if I needed them.these have worked much better than airbags for our coil spring rear suspension to handle the tongue weight of our trailer. The SUV sits level when the trailer is on and it handles bumps and sway better than the airbags did providing much more comfort to us in the vehicle. Unloaded, we don't really notice they are there, unless, we have all the kids and some friends loaded up and you will fell them work when going over bumps.i do all my maintenance on the vehicle's and inspect these regularly and I cant see any wear so far even though we've gone on 6 trips with our trailer with about 5000 miles doing so.
I cant say these are the best for every truck or SUV, but for ours it is the best and I definitely would recommend to others.3491374

Click to Enlarge

Well they are exactly what I thought it would be. Hard for me to say it's what I needed yet.
I installed them on a homemade trailer from a salvaged 2001 base model tacoma. Once I get finished building it out and have some weight in it I'll have a better idea. But from what I've seen so far on a couple test drives they should come into effect when needed.
For reference I building an Tacoma based trailer with an ARE Contractor topper with a Naturnest roof top tent on the very top. So to counter and sway these should be very helpful. At least I hope so. I'm not an engineer but I did stay at an Holliday Inn once.3526287

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The Timbren SES is a simple solution for rear squat when towing. When hitched to my 30' Airstream Globetrotter (8800 GVWR) with a tongue weight around 1200 lbs, my Silverado 2500HD had a bit more squat than is ideal. I shopped airbags but didn't want to spend ~$2K for the set up and didn't want the hassle of installation and forever chasing air leaks. The Timbren SES literally installs on the Silverado in about 15 minutes. So simple. No bags, no compressor, no wiring, no air lines, no leaks. And WAY less expensive to boot. Just returned form a 600+ mile trip and it towed flawlessly.3514480

Click to Enlarge

A very simple and straightforward installation once you get the oem bumper stops off (had a shop do that)
Timbren worked with me as I had a non OEM frame height (vehicle was lower than stock) to recommend the proper kit. Highly recommend contacting timbren if you are unsure of the proper kit to use. Ride is more stable. It does feel stiffer and less bouncy but am looking forward to seeing how it performs with my truck camper. Truck is a 1998 dodge ram 2500. Brake line over left side of axle needed to be secured to prevent damage.3527145

Click to Enlarge

Click to Enlarge

The Timbren overload spring/bumper was east to install and did what it was supposed to do when I hitched up a camp trailer. These did not negatively affect the ride by any means and I don't have to worry about the troubles with air bags.3615169

Click to Enlarge

Stiffens and corrects kneel in rear end of 2023 Chevy Silverado 1500. You will notice a stiffening of the rear end suspension while unloaded, but it’s a fair trade off to prevent sagging and porpoising while towing. I found it easier to pull the rear wheels and work from the side than underneath the vehicle while installing.3581087

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The timbres bump stop is exactly the right height to meet the axel when the trailer is connected with all its weight onto the hitch. I have an Andersen weight distribution hitch and it levels out perfectly. The day picture is with the coach (Winn 2100bh) with factory equipment. The night picture is after the timbres are in place. Looks good.3564611

Click to Enlarge

Click to Enlarge

It has been almost a year since I installed Timbren Suspension Enhancement Systems (DVF350 and DVR350R) on the front and rear of my 2003 Dodge RAM Van 3500. These bumpers replaced the OEM bump stops that were on my van. I like the Timbren bumpers much better than the OEM bump stops because they provide a progressively cushioned response for suspension compression when traveling over significant humps like speed bumps in a parking lot, or curb ramps into driveways. I did not like the abrupt stop the OEM bump stops provided when traveling over the same objects. I installed the Timbren rear bumpers first, and after a few months of use, I decided to add them to the front. In both cases, the front and rear Timbren bumpers were easy to install once the OEM bump stops were removed. Installation required reuse of the factory hardware. On my van, the Timbren bumpers are not always engaged. Under normal load and travel conditions the bumpers are relaxed and about 1/2” away from the suspension landing points. However, their presence is much appreciated and very noticeable when the van is carrying heavy loads or handling significant humps.3537594

Click to Enlarge

Click to Enlarge

Absolutely Pleased with the TIMBRENS. They were easy to install, and took less than an hour to install both. I noticed a slight stiffness in the ride as the rear bounced over a bad roadway. Towing is great, with a nice level and smooth ride. I am glad that I did not order the heavier duty Timbrens, than what was recomended for my truck. I believe the ride would have been too stiff. If you look at the photos showing the timbrens, the truck is still lifted in the rear, so what you see is a big gap between the rubber, and the steal plate. When the truck is lowered, there's 1" of space as it should be. BTW, I have been purchasing from etrailer for years now, and I have to say that I have never had any issues with any orders. They are my go to folks for all of my vehicle suppension stuff and trailer stuff. You can't go wrong with buying from them.3315678

Click to Enlarge

Click to Enlarge

Click to Enlarge

My F53 was like driving a waterbed down the road. With the Timbrens, it’s a different vehicle. Should have installed them years ago. Etrailer is my go to for anything trailer. FAST shipping and prompt responses to questions or concerns.3618596

Click to Enlarge

2022 F250 Super Duty. Super easy to install. I have about 3/4" gap between the spring and the plate. Time will tell how they impact the ride quality and how much sag they mitigate with my 5th wheel hooked up.3390201

Click to Enlarge

Timbren Spring Helpers were exactly what I needed on my Tundra plus a spacer kit since I have a 3” TRD lift. They were packaged neatly, with proper hardware, and excellent instructions! They absolutely do exactly what they are supposed to do! Truck rides much better and helps level out the load!3608688

Click to Enlarge

Click to Enlarge

Click to Enlarge

I'm suitably impressed with the difference i feel.
I have about 250 lbs. of static load with my topper and Decked cargo system. This put my install gap with no spacers just under the reccomended 1 inch minimum.Then add a couple hundred more pounds hauling music gear 100 shows a year, and the stop is resting on the axle.
I feel the absorption of the Timbren material is better than the flimsy stock bump stops. More cushion.
Where i really feel the difference is in the stabilty of excessive side sway when turning while loaded.
I have a gig coming up that will involve some unpaved mountain roads to get there so I think i will have a real goid idea of how these Timbren's will perform.
Instalation took me about an hour at 11 p.m.
The product it of the highest quality in design and build.
And Etrailer is a company that I would not hesitate to buy from in the future.
Thanks Dee Dee.
You rawk!!3606053

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

3441075

So happy. Instantly made a difference! 3551412

Difficult to get in but they work great! First side took 3 hours to devise a way to install. Rubber is quite stiff and nearly impossible to manipulate into the factory receiver. Had to take a c clamp and squeeze rubber into a U shape with one end in receiver and massage in with screwdriver and grease. Second side took ten minutes once I had method down. Very gratifying upgrade so far. 2016 Sprinter 4x4. I would consider the 11,ooo pound version if I did it again.3382782

Thank you works well, easy install 3538233