See what our Experts say about this Thomas Payne Accessories and Parts

• Thomas Payne Recliner Has Power But Does Not Work
  This sounds like a faulty control box, and unfortunately that is a pretty common issue with these recliners. To fix it, you'll just have to replace your control box with the Replacement Control Box for Thomas Payne Momentum Recliners and Sofas # 195-387596 if you have the Momentum series recliner, or the Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas # LC36FR if you have the Seismic series recliner. It also wouldn't hurt to do a hard reset before you replace...
  view full answer...
• Troubleshooting A Thomas Payne Recliner That Will Not Recline
  For your Thomas Payne dual reclining loveseat, there could be a number of reasons why your recliner will not recline any longer. Lippert, the manufacturer of these recliners, has recommended you first unplug the unit from power, and let it sit for around 10 minutes. Sometimes a simple turn off, turn on fix is all that is needed to fix an issue. Another thing you can do is swap the cup holders, and see if the functions change on the chairs. If the left side works with the other cup holder,...
  view full answer...
• Which Control Box do I Need for My Thomas Payne Theatre Seating?
  Hello Ernie, I wish I was able to cross reference the serial number, but I am coming up empty handed. Do not be discouraged though, we will make sure we get you the correct control box. You can tell which Thomas Payne series you have by the features on the chair. -Momentum seating has power recline and LED-lit cupholders, but no heat, massage, power headrest, or power lumbar, the controls are simple and usually limited to recline and lights. If this is what you have you will need #...
  view full answer...
• Availability of Replacement Parts to Power the Thomas Payne Momentum RV Dual Reclining Sofa
  We do have some replacement parts for power in regards to the Thomas Payne Momentum RV Dual Reclining Sofa that you referenced. The parts that we have are # 195-387597 for the cup holder, # 195-387596 for the control box, and # 195-387595 for the power cord. The cup holder is self-explanatory but if you are needing to replace one of the other 2 parts and are not sure which one it is, the control box can be located either behind or under your recliner. This is known as the "brains" of...
  view full answer...
• Troubleshooting Heater Not Working on Thomas Payne Recliner but Massage and Lights Work
  I spoke with my contact at Lippert who said that either the heater is bad or the control box needs to be replaced on your Thomas Payne Momentum recliner. To test the heater unplug the red and black wires from the control box (located behind and under your recliner) and test for continuity using a multimeter like part # PTW1714. If you continuity then that means the control box is bad and you can replace it with part # 195-387596. If you don't have continuity then the heater is bad and...
  view full answer...
• Troubleshooting Functions Not Working on Thomas Payne Momentum RV Dual Reclining Sofa
  There are a few possibilities as to why only one side of your Thomas Payne Momentum RV Dual Reclining Sofa is acting up (or not acting up at all in your case). There are 3 components that allow the recliner to operate the lights, massage, and heater. These are the Cup Holder # 195-387597, Control Box # 195-387596, and the 12V Power Cord # 195-387595. To determine which of these components needs to be replaced simply try using parts from the side that is working. Start off by swapping...
  view full answer...
• Troubleshooting Thomas Payne Recliner Power Issues Where Nothing Works
  Since your Thomas Payne Recliner has no power for any function, I recommend first plugging something into the outlet to make sure that isn't the issue. Next, I recommend checking the Cup Holder # 195-387597 and it's wiring connection because that selects the functions as a built in wired remote to the control box. Next check the connections to the control box # 195-387596 itself. Finally check the 12V power cord # 195-387595. There are no external fuses or circuit breakers that would...
  view full answer...
• Troubleshooting the Replacement Cup Holder for Thomas Payne
  To operate the lights on the Cup Holder for Thomas Payne Momentum Recliners and Sofas # 195-387597 you just use the button found on the outer ring of the cup holder (be sure that it is not locked). If when the lights are off, the system is still lit (other than the small spots on the buttons) you likely have a malfunction and will want to unplug the chair to reset it. If that doesn't solve the issue, then the switch is bad and you will need the Replacement Cup Holder for Thomas Payne Momentum...
  view full answer...
• Does etrailer Carry A Replacement eMoMo Controller
  Hey Michael, unfortunately we do not have that controller. I wish there was something else we can do for you, so If you can think of anything please feel free to let me know,
  view full answer...
• Replacement Control Box for Thomas Payne Recliners and Sofas
  Hey Rob, I wasn't able to get any information off of that serial number you gave me. We only have two control modules for the Thomas Payne loveseats. I have listed them below. Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas item # LC36FR Replacement Control Box for Thomas Payne Momentum Recliners and Sofas item # 195-387596 I recommend looking at the pictures of these controllers and comparing them to yours. Hopefully one of them will work as a replacement....
  view full answer...
• Troubleshooting A Thomas Payne Recliner that Won't Retract
  What you can first try, if you have not already, is unplugging and plugging back in the sofa. You'll want to make sure to wait at least 10 minutes before restoring power. It also wouldn't hurt to check the wiring as well, and make sure you're checking for pinched wires or any broken/frayed wires. It is possible that the cupholder has gone bad. Since the cupholders control the functionality on the chairs, you can try and unplug the cupholder and checking to see if it works. If not, you...
  view full answer...
• Thomas Payne Powered Theater Seating Troubleshooting
  The required power for Thomas Payne furniture is 110v AC or 12v DC to power these units. So you could be facing a voltage drop and need to increase the gauge of wire to the outlet you have the unit plugged into. If you have the correct amount of power but the none of the functions are working then your control box is to blame. If you have a Seismic model you'll need the Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas - Qty 1 Item # LC36FR and if you have the...
  view full answer...
• Heater on Thomas Payne Theater Seating Not Working
  There could be 2 different issues here, so I'll give you a way to test out the control box which will help us figure out what the issue might be. To test the heater unplug the red and black wires from the control box (located behind and under your recliner) and test using a multimeter like part # PTW1714. Using the continuity setting on the meter, check and see if there is continuity on the wires of the control box- if you have continuity then that means the control box is bad and you...
  view full answer...
• Troubleshooting Thomas Payne Theater Seat Recliner Seat Heater Not Connected
  It sounds like you have the heating pad in your chairs and are missing the wiring harness that connects the seat heater to everything else. The Replacement Seat Heater Kit for Thomas Payne RV Furniture # 195-000113 connects to the two prong connection from the seat heater you described. It will also connect the heating pad to the remote control and the power supply to get the seat heater up and running.
  view full answer...
• Help Finding Notch to Remove Thomas Payne Cupholder
  I spoke with my contact at Lippert who said that there is a notch in the side of the cup holder that you should be able to feel with your hand. I attached a picture of where it is as well. Once you find it you will need to use a flathead screwdriver or a butter knife to pop it up. This will reveal 2 screws that you will need to take out before detaching the cup holder wiring from the arm. She also said that when the massage function goes out this is typically something that is related...
  view full answer...
  
• Replacement Power Cord For Thomas Payne Recliners And Sofas
  The Replacement 12V Power Cord for Thomas Payne Momentum Recliners And Sofas # 195-387595, will work with the following Thomas Payne Momentum recliner or sofas: -195-000055, 195-000056, 195-000055-056, 195-055-056-058, and 195-055-056-057. If you have the Thomas Payne Seismic Series Recliners, you can use the Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas # 195-000111.
  view full answer...
• Replacement Control Box Options for the Thomas Payne Seismic & Momentum Series Recliners and Sofas
  We do carry a couple of replacement control boxes like the Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas # LC36FR which will work with the Seismic series recliner and sofas, and the Replacement Control Box for Thomas Payne Momentum Recliners and Sofas # 195-387596 which will work with Momentum series recliners and sofas. If you have one or the other series of recliners mentioned above, this replacement will work great for you. If you do not, then unfortunately...
  view full answer...
  
• Troubleshooting Thomas Payne RV Couch Cupholder Buttons Flashing
  Sounds like possibly a loose connection to the cupholder wiring connectors of your Thomas Payne couch or the cupholder wiring is bad and would need to be replaced. For a replacement we have the part # 195-387597 which in the product pictures you can see how it connects to the couch's wiring. Also it could be a control box like the part # 195-387596 for if you have a Momentum. To test if it's a control box what you can do is swap the left side control box with the right side. If the problem...
  view full answer...
• How To Tell If I Need To Replace The Cup Holder Or Control Box On A Thomas Payne Momentum Recliner
  From what you are describing, you have a short in one of two places. First is the cup holder # 195-387597 that has the controls for these functions and would explain the odd things it is now doing. However, it could also be the control box # 195-387596. The best way to find the culprit is to remove the cup holder from the side that is working properly and plug it into the side that is misbehaving. If this fixes everything, you will need to replace your cup holder with the # 195-387597....
  view full answer...
• Is There a Fuse in the Replacement Control Box for Thomas Payne Momentum Recliners and Sofas
  The Replacement Control Box for Thomas Payne Momentum Recliners and Sofas part # 195-387596 does not contain a fuse. The small black plug is designed to plug directly in to the existing plug on the sofa or recliner and is a direct replacement for the Momentum series from Thomas Payne
  view full answer...
• How to Remove Cup Holder from Thomas Payne Momentum RV Dual Reclining Sofa
  I spoke with my contact at Lippert who said that there is a notch in the side of the cup holder that you should be able to feel with your hand. Once you find it you will need to use a flathead screwdriver or a butter knife to pop it up. This will reveal 2 screws that you will need to take out before detaching the cup holder wiring from the arm. She also said that when the massage function goes out this is typically something that is related to the control box. This is found under the chair...
  view full answer...
• Troubleshooting A Thomas Payne Recliner That Has Lights That Don't Turn Off
  Since you mentioned you've already replaced your cupholder # 195-387597, and your power cord # 195-387595, I suggest you try to reset the chair if not preformed already. You'll want to unplug the unit from power, and let it set for about 10 minutes. Then plug the unit back into power, and check for functionality. If that doesn't fix it, then since you've already replaced your power unit and the cupholder, you'll more than likely need to replace the control box # 195-387596.
  view full answer...
• How are RV Recliners With Heat and Massage Functions Powered
  The recliners run off of 110V AC, using a standard 110V outlet. So, if your camper doesn't already have a power inverter you could use one like the Go Power # 34280176. If your loveseat is a Thomas Payne model, you can use the # 195-387595 replacement power cord if yours is missing.
  view full answer...
• Troubleshooting Lights on Thomas Payne Momentum RV Dual Reclining Sofa
  If the lights are not working on your Thomas Payne Momentum RV Dual Reclining Sofa 195-055-056-058 first just try unplugging it from your outlet. If that does not work you should unplug the 12V cords from the back of the sofa and then reconnect them. I have added a link to a video which shows how you can do this; it will be at about the 4:00 mark in the video. Should you need replacement parts to fix the issue we carry the Replacement 12V Cord for Thomas Payne Momentum Recliners and Sofas...
  view full answer...

Do you have a question about this Accessories and Part?