See what our Experts say about this Thomas Payne Accessories and Parts

• Troubleshooting A Thomas Payne Recliner That Will Not Recline
  For your Thomas Payne dual reclining loveseat, there could be a number of reasons why your recliner will not recline any longer. Lippert, the manufacturer of these recliners, has recommended you first unplug the unit from power, and let it sit for around 10 minutes. Sometimes a simple turn off, turn on fix is all that is needed to fix an issue. Another thing you can do is swap the cup holders, and see if the functions change on the chairs. If the left side works with the other cup holder,...
  view full answer...
• What Does Plug on Thomas Payne Momentum Reclinder Connect to
  Thank you for the pictures. I spoke with my contact at Lippert and he said that the connector you are showing on your Thomas Payne Momentum recliner is what connects to your cup holders, like part # 195-387597, for controlling the heat, massage, and LED lights. Once you connect that to the wire from your cup holder you should be able to use the features on your recliner.
  view full answer...
  
• How to Remove Cup Holder From Thomas Payne Momentum Furniture
  If you need to remove one of the cup holder assemblies on your Thomas Payne Momentum Recliner you can do so by first locating the notch on the side of the cup holder that you should be able to feel with your hand. Then it's just a matter of using something like a flathead screwdriver to pop up the cup holder using this notch. Once the unit is popped up from its recessed opening there will be 2 screws revealed that need to be removed before you can completely detach the cup holder wiring...
  view full answer...
• Troubleshooting Thomas Payne RV Love Seat with Cupholder That Light Flickers
  What seat do you have? It sounds like it's a bad cupholder based on what you mentioned and if you have a Thomas Payne Momentum setup the part # 195-387597 that you referenced would be correct for it.
  view full answer...
  
• Troubleshooting Functions Not Working on Thomas Payne Momentum RV Dual Reclining Sofa
  There are a few possibilities as to why only one side of your Thomas Payne Momentum RV Dual Reclining Sofa is acting up (or not acting up at all in your case). There are 3 components that allow the recliner to operate the lights, massage, and heater. These are the Cup Holder # 195-387597, Control Box # 195-387596, and the 12V Power Cord # 195-387595. To determine which of these components needs to be replaced simply try using parts from the side that is working. Start off by swapping...
  view full answer...
• Troubleshooting the Replacement Cup Holder for Thomas Payne
  To operate the lights on the Cup Holder for Thomas Payne Momentum Recliners and Sofas # 195-387597 you just use the button found on the outer ring of the cup holder (be sure that it is not locked). If when the lights are off, the system is still lit (other than the small spots on the buttons) you likely have a malfunction and will want to unplug the chair to reset it. If that doesn't solve the issue, then the switch is bad and you will need the Replacement Cup Holder for Thomas Payne Momentum...
  view full answer...
• Availability of Replacement Parts to Power the Thomas Payne Momentum RV Dual Reclining Sofa
  We do have some replacement parts for power in regards to the Thomas Payne Momentum RV Dual Reclining Sofa that you referenced. The parts that we have are # 195-387597 for the cup holder, # 195-387596 for the control box, and # 195-387595 for the power cord. The cup holder is self-explanatory but if you are needing to replace one of the other 2 parts and are not sure which one it is, the control box can be located either behind or under your recliner. This is known as the "brains" of...
  view full answer...
• Troubleshooting Thomas Payne Recliner Power Issues Where Nothing Works
  Since your Thomas Payne Recliner has no power for any function, I recommend first plugging something into the outlet to make sure that isn't the issue. Next, I recommend checking the Cup Holder # 195-387597 and it's wiring connection because that selects the functions as a built in wired remote to the control box. Next check the connections to the control box # 195-387596 itself. Finally check the 12V power cord # 195-387595. There are no external fuses or circuit breakers that would...
  view full answer...
• Who Makes Thomas Payne Recliners? Is There A Manual Release For The Footrest?
  What you have there is a Thomas Payne brand Recliner which is made by Lippert Components. I am not aware of a manual release for the foot rest. A lot of times issues like this are the result of a bad control box. This would not be something we carry here at etrailer. Your best bet would be to reach out to Lippert directly.
  view full answer...
  
• Replacement Cupholder And Controller For Thomas Payne Momentum Recliner
  Your best bet will be to get the Replacement Cup Holder for Thomas Payne Momentum Recliners # 195-387597, since the plastic cover is not available separately. This will be a direct replacement for the cupholder with the heat, massage and LED buttons. Since the heat does not function, this is likely due to a bad controller. For a replacement controller you will need the Replacement Control Box # 195-387596, which will be a direct replacement for your momentum recliner.
  view full answer...
• Troubleshooting Thomas Payne RV Recliner Where Power Functions Stopped Working
  Try removing the good working cupholder and installing it on the side that isn't working. Most likely that will fix the issue and indicates that you need a new cupholder like with the part # 195-387597 that you referenced.
  view full answer...
• Is My Thomas Payne Recliner The Momentum Series Or Seismic Series?
  The best way to determine if you have the Momentum or Seismic Series recliner is to look at the buttons on the Cupholder. The Momentum series should have only 3 buttons on the cupholder for light, massage and heat. The Seismic series will have 5 buttons. Light, open, close, massage, and heat. I have included pictures of both below for your reference. It sounds like yours does have all 5 functions on the cupholder controls, which would mean yours is the Seismic Series. If the the controls...
  view full answer...
  
• Troubleshooting A Thomas Payne Recliner that Won't Retract
  What you can first try, if you have not already, is unplugging and plugging back in the sofa. You'll want to make sure to wait at least 10 minutes before restoring power. It also wouldn't hurt to check the wiring as well, and make sure you're checking for pinched wires or any broken/frayed wires. It is possible that the cupholder has gone bad. Since the cupholders control the functionality on the chairs, you can try and unplug the cupholder and checking to see if it works. If not, you...
  view full answer...
• Troubleshooting Thomas Payne Recline Power Issue
  Since your Thomas Payne Recliner has no power for any function, I recommend first plugging something into the outlet to make sure that it is properly running and is not the issue. I would then check the cup holder # 195-387597 and the wiring connection because that controls all the functions as a built in wired remote to the control box. Then I would check the connections to the control box # 195-387596. Finally I would check the 12V power cord # 195-387595. There are no external fuses...
  view full answer...
  
• How To Tell If I Need To Replace The Cup Holder Or Control Box On A Thomas Payne Momentum Recliner
  From what you are describing, you have a short in one of two places. First is the cup holder # 195-387597 that has the controls for these functions and would explain the odd things it is now doing. However, it could also be the control box # 195-387596. The best way to find the culprit is to remove the cup holder from the side that is working properly and plug it into the side that is misbehaving. If this fixes everything, you will need to replace your cup holder with the # 195-387597....
  view full answer...
• Help Finding Notch to Remove Thomas Payne Cupholder
  I spoke with my contact at Lippert who said that there is a notch in the side of the cup holder that you should be able to feel with your hand. I attached a picture of where it is as well. Once you find it you will need to use a flathead screwdriver or a butter knife to pop it up. This will reveal 2 screws that you will need to take out before detaching the cup holder wiring from the arm. She also said that when the massage function goes out this is typically something that is related...
  view full answer...
  
• Troubleshooting Heater Function of Thomas Payne Power Recliner that Stopped Working on One Side
  We've checked with Thomas Payne about this issue in the past and they said that either the heater is bad or the control box needs to be replaced on your Thomas Payne Momentum recliner. To test the heater unplug the red and black wires from the control box (located behind and under your recliner) and test for continuity using a multimeter like part # PTW1714. If you have continuity then that means the control box is bad and you can replace it with part # 195-387596. If you don't have continuity...
  view full answer...
• How Does Thomas Payne RV Sofa Cupholder Remove
  I spoke with my contact at Lippert who said that there is a notch in the side of the cup holder that you should be able to feel with your hand. Once you find it you will need to use a flathead screwdriver or a butter knife to pop it up. This will reveal 2 screws that you will need to take out before detaching the cup holder wiring from the arm.
  view full answer...
• Recliner Feature Not Working On Thomas Payne Theater Seating But Lights and Heat Do
  The issue you are experiencing with your Thomas Payne Theater Seating could be either the control box or cup holder. In order to determine which is the issue you will simply need to swap out one side for the other and see if the problem continues on that side. If you have the momentum series then the part number of the control box is part # 195-387596 and the part number for the cup holder is part # 195-387597.
  view full answer...
• How to Remove Cupholder From Thomas Payne Momentum Recliner
  If you need to remove one of the cup holder assemblies on your Thomas Payne Momentum Recliner you can do so by first locating the notch on the side of the cup holder that you should be able to feel with your hand. Then it's just a matter of using something like a flathead screwdriver to pop up the cup holder using this notch. Once the unit is popped up from its recessed opening there will be 2 screws revealed that need to be removed before you can completely detach the cup holder wiring...
  view full answer...
• Replacement Cup Holder for a Thomas Payne Double Recliner
  The Replacement Cup Holder for Thomas Payne Momentum Recliners # 195-387597 will work for the Momentum series recliners (#'s 195-000055, 195-000056, 195-000055-056, 195-055-056-058, and 195-055-056-057) if you have one of those models then this will work for you. But it sounds like you have a double recliner with power recline which the # 195-387597 does not have. The Momentum series has release handles between the seat cushion and arm of the recliners to activate the footrests. The Replacement...
  view full answer...
• Troubleshooting Thomas Payne Heated Sofa Where Heat Function isn't Turning On
  You could test the wiring of the heating pad with a circuit tester like the part # PTW2993 to see if there is voltage to it when the heating function is on. If you are getting voltage but the seat isn't heating you'd want to replace the heater with part # 195-000113 like you referenced. If its not the heating element its most likely the cupholder which controls the activation of the pad which is part # 195-387597.
  view full answer...
• Troubleshooting Thomas Payne Seismic Series Recliner That Wont Recline
  I'll start off by saying that the Replacement Cup Holder # 195-387597 is designed for the Momentum series recliners and will not control the opening and closing of your Seismic series sofa seating. Unfortunately we do not have an available cup holder replacement for the Thomas Payne Seismic Power Reclining Sofa. But there are some things we can try to get your sofa back in working order. Lippert, who manufacture the Thomas Payne sofas recommend first unplugging the units and letting them...
  view full answer...
• How To Access Components Under a Thomas Payne Recliner That Has No Power to Open the Foot Rest
  The manufacturer unfortunately did not design a manual release for loss of power. For this reason they recommend not screwing their furniture to the floor, so you'd be able to flip it forward for any repairs. Obviously some times this is out of your control because it was done prior to you owning it. You're going to need to try to access the parts like the Control Box # 195-387596 and the 12V Power Cord # 195-387595 from the back. There are two tabs that hold the back of the recliner on,...
  view full answer...

Do you have a question about this Accessories and Part?