See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Recommended Front Hitch for a 2012 Chevrolet Express Van
  Hey Lawrence, unfortunately it doesn't look like we have any custom front hitches for a 2012 Chevy Express, but we do have universal hitches like # 15903 that will work but would require you to weld it to your frame. This hitch will work with frames that have a width of 18" to 60" wide, has a max weight capacity of 15,000 lbs, and has a max tongue weight capacity of 1,500 lbs.
  view full answer...
• What Hitch do You Recommend for My 2012 GMC Savana Utility Van?
  Is the steel step bumper you have installed the factory bumper on your 2012 GMC Savana KUV Van?
  view full answer...
  
• Hitch for 1952 Chevy 3100 Pickup Truck
  The only hitch that would work for you is a weld-on such as the Curt # 15903. This is a universal hitch that is a Class V with a 2" receiver and works with frames that are between 18" and 61". I have attached a link to the installation instructions for you to take a look at.
  view full answer...
• Recommended Weld On Universal Fit Class 5 Trailer Hitch for BlueBird All American Bus Diesel Pusher
  For your BlueBird School Bus conversion, there isn't a specific confirmed fit Class 5 trailer hitch receiver. The universal fit weld on hitch is your best option. The Class V Universal Weld-on Receiver Hitch # 15903 you asked from is a great option as is the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41991-07. Both of these will have a 2 inch receiver opening. These hitches will need to be welded bare metal to metal for the correct strength....
  view full answer...
• Trailer Hitch Option For Winnebago Fuse
  Hello Arthur, There isn't anything specifically made for your Winnebago Fuse or Ford Transit chassis, so the only thing you can do is put on a universal weld-on hitch. I recommend taking a look at the Curt # 15903 which gets welded onto frames up to 60 inches wide and provides a drop from the frame of 11-1/2 inches. You'll need to measure to see if that'll work for you, and if not I have added a link below to our entire selection of weld-on hitches.
  view full answer...
• Is There A Trailer Hitch For The 2013 Mercedes-Benz ML350 Bluetec?
  Hello Silvio, thanks for reaching out. The hitches that we offer for the 2013 Mercedes-Benz M-class, the Curt # C13411 and the Draw-Tite # 76141, will only fit gasoline models. Since your ML350 Bluetec is a Diesel, these hitches will not fit. Unfortunately we do not offer anything for the Diesel models at this time. Your only option would be to take a Universal Weld-On hitch like the Curt # 15903 and have a professional welder fabricate something to fit.
  view full answer...
• Can A Blue Ox Baseplate And Curt Front-Mounted Trailer Hitch Both Be Installed On A 2022 Ram 1500
  Hey Mike, Both the Blue Ox Base Plate Kit # BLU99FR and Curt Front Mount Trailer Hitch Receiver # C87FR would be fighting for the same space on the frame rail where the tow hooks sit so they would not be compatible together. There isn't another custom-fit hitch but you could go with a weld-on adjustable-fit trailer hitch and work with a local fabricator shop to get it sitting right and welded to the frame rails. We offer a few different drop lengths that you can use as a rise or drop...
  view full answer...
• Front Mounted Trailer Hitch Receiver Options For A 2019 Nissan Titan Pro 4x
  Hi Kevin, There unfortunately isn't a custom-fit front trailer hitch receiver for your 2019 Nissan Titan Pro 4x so you'd have to go with a universal-fit weld-on trailer hitch like I have listed below. These will all come with a specific drop so you'll want to measure from the frame down to see what size drop you'll need in order to clear the front fascia. These will fit an 18" to 44" wide frame width and any excess can just be trimmed off of the crosstube. Draw-Tite 7" Drop # 41990-07 16"...
  view full answer...
• Trailer Hitch Options For A 2018 Thor Outlaw 37BG On A Ford F-53 Chassis
  Hey Steve, For a 2017 F-53 chassis we currently only have weld-on universal fit style trailer hitches available. Each of these would fit 18" to 44" wide trailer frames and would come with brackets that can give you a different drop depending on your needs. You'll want to measure down from the frame to determine where you want the receiver tube to come out to avoid hitting the fascia. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9"...
  view full answer...
• Trailer Hitch Option For Bus
  There isn't anything specific for your Chevy Mid Bus but there is an option for a universal, adjustable weld-on hitch. For example, if your frame was 18" to a maximum of 60" then you could use the Curt Class 5 Universal Weld-on Hitch w/ Brackets # 15903. I have added a link below to our entire selection of weld-on hitches for you.
  view full answer...
• Recommended Hitch for a 1997 Eldorado Aerotech Shuttle Bus Build on a Ford E-450 Chassis
  I have a solution for you but the brackets on the Curt item # 15903 can not be cut and there are no shorter options. I recommend using the Draw-Tite Trailer Hitch item # 41990-07 instead. This is also a class V universal hitch with a 2" receiver. It however includes brackets that provide a 7" drop. It can also be bolted on or welded. I have attached a diagram below so you can compare the dimension of these brackets to your Eldorado's frame to make sure they will work. If you have any...
  view full answer...
  
• Recommended Trailer Hitch For 2000 Spartan Newmar
  I can get the hole dimensions for you of the B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit part # BWHDRH25132 but it is not meant to fit a 2000 spartan MM newmar RV chassis so it will most likely be too narrow since it is designed to fit pick up trucks. I recommend to use a weld on adjustable hitch like Class V Universal Weld-on Receiver Hitch part # 15903. It can be installed on frames from 18" to 61" to fit various trailer frames. It also has a 15000 lb gross towing weight capacity....
  view full answer...
  
• 2010 Blue Bird All American Bus Trailer Hitch Recommendation
  The Draw-Tite Max-E-Loader Trailer Hitch Receiver # 41547 is a custom fit hitch for certain year make models of Ford Super Duty Cab and Chassis trucks. The mounting holes vary in width distance but they are all about 31" apart on center, and the top of the receiver to the vehicle frame will be about 6-1/2". Since you're looking to install a hitch on a bus I recommend looking into a universal heavy duty hitch receiver like the Curt # 15903. This is a weld-on installation that a shop can...
  view full answer...
• Hitch For A 2013 Chevy Express 4500 Cutaway
  We offer universal fit hitches that fit many different vehicles. To add a class IV or V hitch to your 2013 Chevy express 4500 Cutaway from the hitches we carry, would require the hitch to be welded in place. I recommend the Curt Class V Universal Weld-on Receiver Hitch Item # 15903. This hitch fits frame rail spacing from 18" apart up to 61" apart, has a 1500lb max tongue weight with a 15000lb gross towing capacity, a 2" x 2" receiver tube opening with a 5/8" hitch pin hole. I also recommend...
  view full answer...
• How to Increase the Weight Capacity of a Trailer Hitch for an RV
  I do have an option for you but I am not aware of any way to increase the tongue weight capacity of a trailer hitch save for a weight distribution system which does not apply for hitch mounted accessories like a scooter carrier. Therefore, your only option would be to replace the trailer hitch you have now with one rated for more tongue weight and for that I recommend the Class V Universal Weld-on Receiver Hitch part # 15903. If you are not an experienced welder than I recommend taking...
  view full answer...
• Can A Hitch Extender Be Used With A Front Mount Trailer Hitch To Park A Travel Trailer
  Hi Don, Hitch extenders place a lot of stress on the hitch because you're leveraging the weight further out so using one typically drops the capacity by 50% when towing. You'd be doing it in a parking lot situation where you wouldn't really be traveling much just more so maneuvering around so realistically that shouldn't affect you but depending on how much weight you're leveraging there could be a breaking point, we just wouldn't be able to know exactly what that point is. The Curt...
  view full answer...
• Trailer Hitch Receiver Options For A 2025 Ford E-350 Cutaway Van
  Hey Jim, I drew up a little diagram of the Blue Ox Trailer Hitch Receiver # BLU75UR's dimensions so you can see if this would be a fit. It's not listed as a fit for your E-series cutaway chassis but the F and E-series can some times be interchangeable. It is listed to fit the following models: 2017 - 2025 Ford F-250 Super Duty 2017 - 2025 Ford F-350 Super Duty 2017 - 2025 Ford F-450 Super Duty Pickup There isn't a custom-fit option confirmed to fit so if this doesn't your next option...
  view full answer...
• Solution for Trailer Hitch Receiver on 2019 E-450 Cutaway With Lift Gate
  Typically the solution for your 2019 E-450 Cutaway is a universal hitch like the Curt # 15903 you looked at. With the liftgate you will have to figure out if it will fit or not based on the placement and design of the liftgate. Some have too many parts in the way and others may have room for a hitch installation. If you aren't sure i recommend talking to a certified welder or fabricator to see if this is possible based on the position of your liftgate. You could also have a custom hitch...
  view full answer...
• Recommended Flat Tow System for 2018 Chevy Silverado 1500 Crew Cab 4x4
  Your 2018 Chevy Silverado 1500 crew cab 4x4 curb weight is 5,300 lbs based on my research. To flat tow this vehicle, I recommend upgrading your 5,000 lb hitch to the Curt Class V Universal Weld-on Receiver Hitch # 15903 which is a universal fit for frames between 18 and 61 inches wide. Then for your flat towing setup, I recommend you begin with the Roadmaster MX Base Plate Kit - Removable Arms # RM-3176-3 and use Loctite Threadlocker # LT37420 for the installation. Then for your tow...
  view full answer...
• Recommended High Capacity Hitch and Dual Ball Mount for a 2003 Bluebird Bus
  I have a solution for adding a heavy duty hitch to your 2003 Bluebird bus but there aren't any TorkLift SuperHitches that will work because they are all custom fit. You will need to go with a universal option and the one I recommend is the Curt Class 5 Universal Weld-on Hitch w/ Brackets item # 15903. This is a class V hitch with a 2" receiver. It has a 15,000 lbs towing capacity and a 1,500 lbs maximum tongue weight. This hitch must be welded on. There is no way to bolt it to your bus...
  view full answer...
• Best Heavy Duty Trailer Hitch for a 2007 Ford E-450
  For a trailer hitch with a 10,000 gross trailer weight towing capacity that will fit your 2007 Ford E-450, I recommend the Class V Universal Weld-on Receiver Hitch part # 15903. This hitch as the title states is a universal option that will fit frame rails spaced between 18" to 60" apart so your 43" rail spacing will not be a problem whatsoever. It also has a greater towing capacity than you need, 15,000 lbs which is never a bad thing. Please note that in order to install this trailer...
  view full answer...
• Trailer Hitch For A 2001 Ford E450 Super Duty Cut Away Ambulance
  The Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2 inch Receiver # 15903 will work on your 2001 Ford E450. The trailer hitch has a black powder coated finish that helps resist rust and corrosion. It has a strong, secure weld-on attachment. The maximum gross trailer weight is 15,000 pounds and it has a maximum tongue weight up to 1,500 pounds. I would recommend checking your vehicle's manual to find the proper towing capacity of your vehicle. The side brackets fit frames from a...
  view full answer...
• Trailer Hitch Compatible with Liftgate Truck
  We have many hitch options for a truck that has a lift gate, but very few of them are a simple bolt on custom application. Because the locations for attaching lift gates vary, you will need to use a weld on option like the Class V Universal Weld-on Receiver Hitch # 15903. There are many different bracket options for a hitch like # 4907 and # 4916.
  view full answer...
• Front-Mounted Trailer Hitch Options For A 2006 Ram 1500
  Hi Brad, Yes, the Draw-Tite # 65033 sits much lower to clear the air dam, while the Curt Front Mount Trailer Hitch Receiver # 31320 sits higher, requiring you to trim the air dam. These both have a 5,000lb capacity so you should definitely make sure your trailer is under that. If it isn't then you should go with an adjustable-fit weld-on hitch instead to ensure you have the capacity to handle the trailer. You can measure the frame width and measure down to where you have space for the...
  view full answer...
  

Do you have a question about this Heavy Duty Receiver Hitch?