Replacement Control Module for Lippert Electric Coach Step
(163 reviews)
Price: $224.57
In Stock
Replacement Control Module for Lippert Electric Coach Step
Item # LC301702
Retail:$338.95
Our Price: $224.57
You Save: $114.38
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (163)
- Q & A (0)
- Videos (1)
- Photos
Lippert Accessories and Parts - LC301702
- RV and Camper Steps
- Control Module
- Lippert
This replacement control module is the brain that enables your single, double, or triple electric Lippert Coach Step or Stromberg Carlson sliding step to function properly. It attaches underneath the step's base with 4 screws (not included).
Features:
- Replaces the control module that came standard on your single, double, or triple electric Lippert Coach Step or Stromberg Carlson sliding step
- Houses the circuits and electrical components necessary for the step to function properly
- Includes weatherproof wiring and connectors
- Installs underneath the base of your step with 4 self-tapping screws (not included)
301702 Lippert Components (LCI) Control Module/Brain for RV Motorized Steps
SP-164889 Stromberg Carlson Electrical Box and Light for Electric Steps
Video of Replacement Control Module for Lippert Electric Coach Step
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Lippert Components RV and Camper Steps LC301702 Review
Today we're going to be taking a look at the Replacement Control Module for an Electric Coach Step. This replaces the control module that came standard on your single, double, or triple electric Lippert Coach Step, or Stromberg Carlson Sliding Step. This unit simply houses the circuits and electrical components necessary for the step to function properly. It's going to include the weatherproof wiring and connectors. It installs underneath the base of your step with four self-tapping screws. The screws are not included, but when you're ready to install this, you'll remove the self-tapping screws holding the ground wires on your previous module. Then you'll need to disconnect the four pin connector to the motor wiring harness, that will look just like this one.
Disconnect the two pin connector to the motor, it's going to look just like this one. Remove the self-tapping screws holding your module in place, and simply install the new module in reverse order. A few measurements to go over with you real quick and then we're going to go over a few of the wire functions. Edge to edge going this direction, it's going to give us a measurement of 5 13/16". Going this direction, just measuring the box portion, that's going to be 4 1/8". The holes are separated on center going this direction by 3 1/8", and the hole separation on center in this direction, is going to be 5.25". Really nice design.
Again, you're going to have your four pin connector, goes to the motor wiring harness. Two pin connector that goes directly to the motor and then your black wire right here, this is going to be the wire that gets connected for the step light. You're going to have two green wires, these are both ground wires. One grounds the chassis, the other one grounds to the steps. Then your purple wire, located right here, this is going to be for the step light switch.
That's going to do it for today's look at the Replacement Control Module for an Electric Coach Step. Again, this replaces the control module that came standard on your single, double, or triple electric Lippert Coach Step or Stromberg Carlson Sliding Step.
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Defective
- Wrong item was ordered
- Product did not meet expectations
Customer Reviews
Replacement Control Module for Lippert Electric Coach Step - LC301702
Average Customer Rating: 4.8 out of 5 stars (163 Customer Reviews)
This replacement control module is the brain that enables your single, double, or triple electric Lippert Coach Step or Stromberg Carlson sliding step to function properly. It attaches underneath the step's base with 4 screws (not included).by: Gene J08/05/2016
the product was shipped and received at my temporary RV location very rapidly. it worked when i installed it since i was armed with some slight installation tips from product reviews. well done! i always like dealing with etrailer.com cheers. Gene from the Sturgis Motorcycle Rally...
by: Wayne 11/17/2023
Excellent customer service from Mike B, the part was a perfect replacement and fixed my problem, thanks for another great transaction.
by: Dennis07/26/2023
your video was most informative, (better than written directions), however the unit i am replacing did not have a separate swithch wire (purple) so I am unsure haow or where to connect. I have a 2006 Forest River Lexington with a Coach Step one step setup. please advise.
by: Bill 12/11/2021
My 2006 Monaco Diplomat steps stopped retracting and extending completely and reading on etrailer website found others with same problem. Called etrailer to order the correct step module and received it quickly. The module item number was LC301702 and it matched all the plugins and wires except there was a purple wire that was not necessary for my unit which I capped off. Thanks for the help!
by: Stephen08/16/2020
Excellent control module. Everything worked when the steps were mounted and plugged in. Very happy with your service. I was able to track my package across the US and Canada. Arrived on time that was stated.
by: Clif07/25/2023
Part works great and was the correct one etrailer had recommended as the replacement needed.
by: Larry03/27/2023
The step controller was the right one, and was verified during order placement. Said it would be there by Friday, but came on Monday. $xxx cheaper than PPL for the exact same controller.
by: Dan 11/07/2021
Its been a few months since receiving the new controller. I finally got around to installing it. All seems to work well! Fixed old controller problems so far!
Dan
11/8/2022
The step controller has been working great! No problems!
by: Jerry06/22/2023
Same name brand part sold by many vendors but cheaper than most. The tracking was interesting. Showed in stock when ordered. Part picked 3 days later. Part packaged 2 days after that. Received by USPS in 3 more. And after 2 more days, I got my part. Good price if you don't mind waiting.
by: Michael02/27/2021
The new replacement module was perfect. Installation was a breeze and now I realize that my old control module was creating more problems that I knew about. Highly recommend this product.
by: Charles 08/23/2023
quick service works great
by: Donald07/14/2023
Not impressed. $[XX] part should last more than 10 months.
by: Dean 05/03/2023
Looks great new updated part for are coachstep system
by: Richard 07/18/2023
module works great so far
by: Richard04/26/2018
I have a 2006 DutchStar. This product was as close to an exact replacement as you can get. The customer service from etrailer was awesome as they checked with Lippert mfg before I order just to make sure it would work and even sent me a pdf of the wiring diagram so I could figure out the install. I was on the road and staying at a KOA, shipping was fast and the box was well enough marked that there was no problem getting it when it arrived.
Richard H.
4/26/2019
actually ... its been two years. No issue since the install!!!
by: Randy c03/23/2016
current step no longer operated when opening and closing door, replaced with sp -164889 electrical box , part arrived quickly and within 30 minutes had this installed and steps working like new . great service
Randy C.
2/20/2018
STILL WORKING GREAT!!!
by: Len P.06/07/2017
Very pleased with staff and service at etrailer! They were helpful in determining the proper product. Received the part very quickly and installed it. But....then realized it was not compatible with the door magnets; however, was able to get the right magnets and send out immediately. Very pleased that the problem was rectified so quickly.
Len P.
6/7/2018
So far...so good.
by: DK04/13/2023
It's been working like clockwork. Very dependable.
by: Don S07/12/2017
The control module for the electric step on our RV stopped working because it became corroded from sprayed sand and water. The new unit is much better designed and fully insulated against a repeat of the problem. It works very well and was delivered as promised. I am pleased with the service.
Don S.
8/1/2018
Thank you for reminding me that I had purchased the Lippert Components Accessories. I am pleased to report that it has worked perfectly from the date that I installed it. The delivery was on time and the instruction information helpful. All told, I am pleased with the service and the improvement in the module. It is greatly improved.
by: Gene K.02/15/2019
Product is RV step controller, and was an exact replacement for old device. Fit perfectly, and works as it should. Be careful of motor plug orientation--if wrong, device opens/closes door opposite correct way. Price was good.
Gene
2/11/2020
Working as it should.
by: Wayne D.12/10/2018
Received the LC301702 control box quickly and installed. This control box resolved my inoperable step problem. I have the Double Coach step installed on my 2005 Newmar Kountry Star DP. On my installation the purple and black wires for the step light were not required. I taped and seal the ends of those wires, attached the control box ground wires one to the step and one to the frame then plugged in the two wiring harnesses as shown in the video. Bam my steps are operational again. Thanks E-trailer.
by: Bill K07/26/2020
Great Purchase. Solid customer service. One call and they quickly diagnosed my problem after I explained the issue. Gave them my part number number and they recommended this part. Self-install and I'm not a mechanic. The Control Board for the electric steps fit into the existing holes. One extra wire I didn't know what to do with, so I just didn't hook it up. Steps work. Every time.
by: Howard03/14/2018
Ordered this while on the road. Great service from etrailer, Brian took order and shipped to my next location where it was waiting for me. New unit bolted and plugged right in, works perfectly. Old controller failed after 10 years exposure to wet roads covered with corrosive crud. New controller is fully potted in rubberized compound which completely seals electronic parts from the elements, rather than old style conformal coating, so new unit should be more reliable.
by: Reese 01/25/2023
Worked as it should and is still working
by: Gene W04/20/2016
Product was just as described, easy to install and works great. This module is a real upgrade from the OEM module. The wiring was pretty much plug and play. A tip from a previous review explained the black wire goes to the step light and the purple wire did not apply to this installation. Great customer service!
25
163
Show More Reviews
See what our Experts say about this Lippert Accessories and Parts
- Replacement Control Module for Coach Step Model 725-0041I spoke with my contact at Lippert and he said the correct replacement control module for your existing Coach model 725-0041 is the part # LC301702. He said this is an exact replacement part and will work perfectly.
view full answer... - Troubleshooting Two Coachsteps That Will Not ExtendIf both of your Lippert Coachsteps are failing to extend it seems like you are on the money with the power or ground issue. Start with the ground wire and make sure it is connected to a clean surface or possibly relocate it if you can and that may just solve the issue. There may also be a short in the wiring to the common power source so use a circuit tester and check to see if you are getting the appropriate voltage and look for broken or damaged wiring which you will need to replace.
view full answer... - Placement Of the Gear When Replacing A Lippert Electric Coach Step Module While the steps are extended the flat gear should sit right at the stop on the right that you referenced (and is pictured below). As the steps close the gear will slide to the left, away from the stop and the control module # LC301702 in the picture.
view full answer...
- Troubleshooting Powered Lippert Steps on RV That Motor Works But Door Switch Does Not Work BypassedBasically you've already troubleshooted your problem to be the controller/module since the motor you know works and the door switch isn't the problem either. If you have a single, double, or triple electric Lippert Coach Step or Stromberg Carlson sliding step the module part # LC301702 that you referenced is the correct part you'd need.
view full answer... - Coach Step Control Module ReplacementThe Replacement Control Module for Lippert Electric Coach Step Item # LC301702 will replace the control module on any Coach Step from Lippert.
view full answer...
- Troubleshooting Lippert Coach Step Clicking Sound When Extending or Retracting All The WayThe clicking sound you are getting of your coach step seemingly wanting to over extend or over retract is not a motor issue but rather a control module issue. This is basically the brains of the operation and if another item wasn't working correctly you'd know in other ways because the gears would slip. I recommend replacing the Control Module with # LC301702.
view full answer... - Replacement for SCS/Frigette Coach Step Controller Part 202-3230The correct replacement control model for the SCS/Frigette Coach Step Controller part 202-3230 is the Replacement Control Module for Lippert Electric Coach Step part # LC301702.
view full answer... - Replacement Control Module for Coach Step 725-0023For the Coach step 725-0023 the correct control module replacement is the part # LC301702.
view full answer... - Wiring Diagram for Coach StepThe Replacement Control Module for Lippert Electric Coach Step # LC301702 is the correct fit for your Lippert Coach step. The long green wire with the ring terminal is your ground and will be attached bare metal to metal on our coach frame. The short green wire is your ground connection to the step frame. The purple wire is an optional light switch that can be connected to your "porch" light. The black wire connects to your step light. The two pin connector goes directly to the motor,...
view full answer...
- Replacement Module Recommendation for RV Coach Steps that Do Not Retract ProperlySounds like you have a module issue. When the Coach Steps stop retracting and extending when they are supposed the solution is to replace the module. For that you'd need the part # LC301702. This is the brain of the system that tells the step motor when it's supposed to power in and power out the steps.
view full answer... - Wiring Control Module LC301702Thank you for the photo and your purchase from etrailer of the Replacement Control Module for Lippert Electric Coach Step # LC301702. I have added some text as well as a diagram for you in regards to how you wire the step. You will need to isolate the brown wire and connect that to the door switch
view full answer...
- Troubleshooting Power Steps on Trailer that Only Operate When Bypassing Controle ModuleThe fact that the power steps on your Newmar Kountry Star seem to operate fine when bypassing the control module does point to the controller being the issue. The other possibility is that the door switch on your trailer is bad, which you can also rule out by testing it with your circuit tester. The Replacement Control Module # LC301702 that you were looking at is designed for single, double, and triple electric Lippert or Stromberg Carlson step assemblies and should work well. If you...
view full answer... - Recommended Replacement Control Module For Frigette 202-3230 For RV Electric StepsThe Replacement Control Module, part # LC301702 is just what you need to replace the Frigette 202-3230 controller on your RV steps. This unit installs under the step base and requires 4 screws for installation which are not included.
view full answer... - Tread Lite Power Steps Won't ExtendI spoke to my contact at Lippert and they informed me that you need to check that you are getting 1.5 to 3 amps coming from the control module. If you are, then test the brake by adding power and ground to the brake leads. (polarity doesn’t matter). I’m suspecting that the brake is bad and not releasing or the brake pad is seized to the pressure plate. I have attached a wiring diagram for you. Please let me know what you come back with and the part number of your steps if replacement parts...
view full answer...
- Troubleshooting Wiring for Coach Step Not Showing PowerThanks for the info! It sounds like you have a Coach Step that uses the Control Module # LC301702. I'm attaching a cutout from the manual for the Coach Steps that shows what connections are what - it looks like you've done a good job at labeling pretty much everything! Usually when you see weird stuff with power (especially a blown fuse) the first culprit to check is the ground. Check the grounds (green wires) and make sure they are securely connected to a clean, bare-metal surface. Any...
view full answer...
- Troubleshooting Step Light Remaining on After Installing Lippert Electric Coach Step Control ModuleThe Lippert Electric Coach Step Control Module # LC301702 is the correct part for both Lippert and Stromberg Carlson brands of electric RV steps. The black wire on this part connects to the step light, and the purple wire connects to the step light's switch. It sounds like the black and purple wires may be reversed in your installation. Please refer to the linked video which details the functions of each wire on this part.
view full answer... - Troubleshooting a Control Module # 909506000 on a Kwikee StepA Control Module for Lippert Electric Coach Step # LC301702 will not have power coming out unless the circuit is activated to control the steps. When the steps are activated the Control Module will send the signal to the motor and you'll see power coming out.
view full answer... - Wiring Replacement Control Module for Lippert Electric Coach Step on Unit without Power SwitchIf you do not have a power switch for your Lippert Electric Coach Step, you can simply tie off the white wire from the Replacement Control Module # LC301702 referenced in your question. For your particular application, this wire will not be needed so you do not need to connect it to anything. The yellow wire from the control module will get run to a keyed power source. It will only power with the ignition on.
view full answer... - Replaced Control Module on Coach Steps but Still No FunctionCan you please confirm the part number on your original control module? They all look very similar but there are internal differences that could affect functionality so I would need to confirm this first. If you in fact have the correct control module then the two prong plug you are referring is the power and ground wires for the motor. These can be tricky to check as the continuity will alternate between wires depending on which direction the step is moving. I recommend removing the motor...
view full answer... - What Is the Black Wire For on the Replacement Control Module for Lippert Electric Coach Steps?The single black wire on the Replacement Control Module for Lippert Electric Coach Step # LC301702 is used for the step light. The green wires to ground, one grounds the chassis, the other one grounds to the steps and the purple wire is for the step light switch. Since your steps are only working partly that would indicate to me that there may be a grounding issue. I recommend checking out your grounds and ensuring they are secured properly. It wouldn't hurt to go through your connections...
view full answer... - Will Replacement Control Module for Lippert Electric Step Work For 2005 Newmar Dutch Star TrailerIf the electric coach steps on your 2005 Newmar are either a Stomberg Carlson or Lippert brand, then the Replacement Control Module, part # LC301702 will work for you. If you can remove the control module on your trailer, it should have some identifying numbers on the switch. If you get those numbers you can let me know what they are and I will be glad to check with Lippert to see if the # LC301702 is the correct replacement for your steps.
view full answer... - Does Replacement Control Module # LC301702 Need to Be Grounded Like Old ModuleIdeally yes you would ground the wires of the Replacement Control Module # LC301702 in the same locations as what you current setup has. As long as they are grounded to the chassis directly or indirectly the module will work great though.
view full answer... - Coachstep on 2007 Holiday Rambler Endeavor Does Not ExtendI have included a picture that shows the troubleshooting steps for the Coachstep brand of RV steps. These steps cover a variety of possible issues. To me it sounds like the control module needs to be replaced, # LC301702. But performing the various tests will narrow done the possible causes.
view full answer...
- Kwikee Steps Will Not Lock Out After 1800709 Module ReplacementIf you can provide me with the part number for the control module that you replaced the Kwikee Step Control Module 1800709 wish I could then verify for you if the correct replacement was used but without this information there would be no way to do so. I spoke to my contact at Lippert about the issue you were having with the lockout not functioning and they stated that you need to test the 4-way plug on the unit which can be seen in the attached photo. I have also attached a photo of the...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Edited by:
Lindsey S
Installed by:
Cole B
Written by:
Chelsea B
Updated by:
Wilson B
Updated by:
Halie H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Bill
12/12/2022
Works great and is a better design than the original is sealed to keep moisture out of the electronics. It also fit perfectly.