Available Replacement Parts for 50 Amp Hughes Autoformers Voltage Booster with Surge Protection

Question

Question:

Hughes RV220-50-SP Autotransformer Where are replacement parts on your web site?

asked by: Roger

0

Expert Reply:

The only replacement part we have for the 50 Amp Hughes Autoformers Voltage Booster with Surge Protection HU57FR is the Replacement Surge Protector # HU26FR.

We do have some other accessories though which I'm linking for you to filter through.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hey Pat, The Rhino box definitely is shorter than what most Rver's were hoping for so we get this question all the time. Switching to a MORryde Cushioned pin box designed with a Rhino box bolt pattern unfortunately won't give you extra…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Jesse; the only reason I can really think of is your bolt pattern. If you have a 1621 bolt pattern there is no reason why you wouldn't be able to use the lower rated Curt Flex Air 5th Wheel Pin Box - Lippert 1621 - 18,000 lbs #LC328492 you…

view full answer...

Answer 7

Hey Dwyane yes that is necessary unfortunately. We do have disc brake kits like the DeeMaxx Disc Brake Kit #DE68YR which will work with 7,000 lb axles that uses specific bearings. The last couple of things you'd need is a brake line kit…

view full answer...

Answer 8

Hey Mark, since we know your trailer has two 7k axles and a bolt pattern of 8 on 6-1/2 inch the correct DeeMax disc brake kit would be the part #DE66AR which comes with everything needed to add electric over hydraulic DeeMax brakes to your trailer.

view full answer...

Answer 9

Hey Guy, While I can't answer that directly as I don't know what axles you have, I can tell you how to figure out if the right kit for you is the DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers #DE66AR. What it comes down to is…

view full answer...

Answer 10

Hi Kevin; the answer to your question is yes. The DeeMaxx Disc Brake Kit w/ Actuator #DE66AR will work with your 2024 Ram factory brake controller.

view full answer...

Answer 11

Hello Merle, thanks for reaching out. The Hydrastar Disc Brake Kit #HSE7K-T1 you were looking at is for a standard 7K axle. The hubs use the #25580 inner bearing, #14125A outer bearing and #GS-2250DL (2.25" ID, 3.376" OD) seal. Most 6K…

view full answer...

Answer 12

Hello Darren. Thanks for reaching out, I can definitely help with this. To convert your 2024 Brinkley Z2900 5th wheel over to disc brakes, you will need a disc brake kit, a brake line kit, and electric over hydraulic actuator, and a breakaway kit for…

view full answer...

Available Replacement Parts for 50 Amp Hughes Autoformers Voltage Booster with Surge Protection

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching