Hitch and Lock for 2022 Winnebago Revel Motorhome

Question

Question:

I need a trailer hitch lock that will work on a Revel Van. Any recommendations?

asked by: Jeanie B

0

Expert Reply:

Since the 2022 Winnebago Revel is built on a long wheelbase Mercedes Sprinter chassis you could use the Curt hitch part # C13388 for a hitch and then for a hitch lock the # HRLHP2 would work great.

expert reply by: Jameson C

0

Answer 1

Your 2015 Freightliner Mercedes Sprinter 3500 with the 144 inch wheelbase and factory step bumper is indeed compatible with the Curt Trailer Hitch Receiver #13375. The brackets and step frame do fit together, as you'll remove the factory…

view full answer...

Answer 2

We haven't had the chance to install both the Curt #C13388 and Draw-Tite #75549 trailer hitches on the Mercedes Sprinter to do a comparison, however I did go out to our warehouse to take a measurement on each to determine which will sit higher…

view full answer...

Answer 3

The Draw-Tite Max-Frame Trailer Hitch Receiver part #75549 is a fit for a 2015 Mercedes-Benz Sprinter Passenger Model with Standard Bumper but you do need to be sure you don't have the 30-3/8" frame, measured outside to outside of frame. I…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver #C13388 will not fit your 2020 Mercedes Sprinter 3500XD with the 170" wheel base. I measured the receiver in our shop and it 33-1/2" wide between the frame rail mounting points. We do also have the Curt…

view full answer...

Answer 5

The receiver on Draw-Tite trailer hitch #75549 does stick out past the bumper a few inches on the 2017 Mercedes Sprinter 2500. Take a look at the picture I have included for an example. There isn't a whole lot of space and no grip on the metal…

view full answer...

Answer 6

The trailer hitch we offer for your 2016 Mercedes-Benz Sprinter 2500 that sits the highest will be the Curt #C13388 which fits right under the rear bumper like the picture I attached. It will sit about 1-1/4 inch taller than the Draw Tite.

view full answer...

Answer 7

The hitches that fit the 2021 Mercedes Benz Sprinter 2500 with the step bumpers like part #75601 do sit lower than the vehicles that do not have the step bumper like part #75549. If you check out the two picture I attached you can see that the…

view full answer...

Answer 8

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13388 is a confirmed fit for your 2012 Mercedes-Benz Sprinter. The reason the hitch does not fit models with 30-3/8" frame, measured outside to outside of frame is because the…

view full answer...

Answer 9

There isn't going to be any noticeable difference in the fit between the Draw-Tite Trailer Hitch #75549 and Curt Trailer Hitch #C13388 that fit your 2019 Mercedes-Benz Sprinter 2500 with a 170 inch wheelbase and standard bumper. The reason for…

view full answer...

Answer 10

The Curt Trailer Hitch Receiver #13375 for your 2022 Mercedes-Benz Sprinter 3500 is 32-1/8" wide between the mounting brackets(see image).

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Hitch and Lock for 2022 Winnebago Revel Motorhome

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching