Parts Needed To Install Trailer Brake Controller In 2018 Toyota RAV4 Adventure
Question:
Hi, I have a 2018 Rav4 Adventure and want to add a brake controller so I can tow a trailer with electric brakes. Where does the trigger signal wire attach? I’ve read that it should go to the “cold side” of the brake switch but some say because of abs, led lighting and cruise control, this may not be the best place. So where do you recommend connecting the trigger wire? Also how much current does this connection require? It also has adaptive cruise control which applies the brakes without pushing on the pedal. I think this would mean that either it’s not advisable to use cruise control when towing or using the connection to the middle brake light would be better so that the trailer brakes are applied whenever the brakes are used. What’s your opinion? Thx
asked by: Bruce P
Expert Reply:
I would be happy to help you get the parts you need to install a trailer brake controller in your 2018 Toyota RAV4 Adventure.
You are correct that the best place to connect the red brake signal wire of a trailer brake controller to a vehicle is the cold side of the stop light switch. Now there are some vehicles where this can be difficult so Tekonsha has mentioned in the past that running it to a third brake light instead is perfectly fine. The stop light switch or third brake light wire will have 12 volts.
Since you have a lot going on with your stop light switch this would be a great alternative.
You will need to to use some # 16-1-1 to run from the trailer brake controller wire to the brake light wire, and use a circuit tester # PTW2993 to find the correct wire to splice in to.
If you do not have already have a 7-way connector or trailer brake controller for your RAV4 then you will need to start with a 4-way connector # 118578. Once a 4-way connector is installed you can install a 7-way connector using # ETBC7. This 7-way will plug in to the newly installed 4-way connector and require just a few more wiring connections. The black wire will get run to the positive terminal of your battery with the included 40 amp circuit breaker, ground the white wire to the frame, and run the blue wire to where the trailer brake controller is being installed.
For a trailer brake controller I recommend the Redarc Tow-Pro Liberty # RED24FR as it is a very low profile controller since only the knob is visible once installed leading to a factory appearing installation. You will also need the Universal wiring harness # RED69FR.
I included videos of the products mentioned for you to take a look at.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Powered Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Hidden
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Redarc Tow-Pro Liberty Brake Controller - Dash Knob - Up to 2 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Plug-In
- Dash-Mounted Knob
- Behind-Dash
- Up to 2 Axles
- Indicator Lights
- Single Trailer Only
- Redarc
more information >
Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Redarc
more information >
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 525 lbs WD TW
- Visible Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Trailer Wiring
- Shop: Redarc Tow-Pro Trail Brake Controller w/ Custom Harness - Dash Knob - Off-Road Mode - Up to 3 Axles
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness - Dash Knob - Up to 2 Axles - Proportional
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Universal Wiring Harness w/ ModuLite and Brake Controller Harness - 7-Way Trailer Connector
- Search Results: tph~022
- Search Results: red69fr
- Search Results: redarc trailer brake controller
- Search Results: etbc7
- Search Results: etbc7
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Shop: Plug-and-Play Wiring Harness for Redarc Tow-Pro Elite or Liberty Trailer Brake Controllers
- Shop: Curt Echo Wireless Brake Controller - 7-Way Plug-in w/ Bluetooth App - Up to 2 Axles - Proportional
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What Size Wire Loom Is Recommended for Trailer 7-Way Wiring
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Video: Installation: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2018 Toyota RAV4
- Q&A: Redarc Tow-Pro Liberty Brake Controller for a 2012 Ford Escape V6 w/ out a Tow Package
- Search Results: spare tire carrier under frame
- Search Results: 7 pin universal wiring kit
- Video: All You Need to Know About the Lippert Spare Tire Winch with Offset Cable
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Q&A: Alternative Installation For A Brake Light Switch Relay Kit On A 2020 Ford Escape Hybrid
- Q&A: Where to Splice Brake Light Wire From Brake Controller To Stoplight Wire
- Q&A: Recommended Brake Controller and Brake Controller Wiring on a 2022 Honda Pilot w/out the Tow Package
- Q&A: Where To Connect Red Wire Of Redarc Tow-Pro Liberty To 2016 Kia Sorento W/ Adaptive Cruise Control
- Shop: Vehicle Tow Bar Brake System
- Shop: Trailer Hitch
- Video: Finding the Right Trailer Wiring Harness
on Trailer Hitch
