Parts Needed To Rebuild Hub On 1985 Shoreline Boat Trailer
Products Featured in This Question
Question:
I have a 1985 shoreline boat trailer and have had a lot of trouble finding a complete replacement hub if it exists. It is a 13inch wheel, 5 bolt x 4.5 inch hub. The spindle diameter is 1.25 1inch where the castle nut screws on the end. The bearings inside are both LM67048. The washers were missing, so I also need the correct ones. Any clues? I see there are kits out there, but I prefer to just replace the whole unit.
asked by: Jon F
Expert Reply:
I have a replacement bearing option for you, but at this time we do not offer a replacement hub that uses # LM67048 as the inner and outer bearing.
You could replace the bearings with # LM67048, and replace the grease seal on each hub as well given there is not severe damage to the hub itself.
To determine the correct replacement grease seal you will need to use digital calipers like # PTW80157 to precisely measure the spindle where the grease seal goes, and the inside of the hub where the grease seal is pressed in.
With these two measurements I will be able to confirm the correct replacement seal for you.
Lastly for a replacement washer you can use the # SW1000 since your spindle has a diameter of 1" where the castle nut goes.
(click to enlarge)
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - LM67048
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing LM67048
- Race LM67010
- 5000 lbs Axle
- 6000 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: 1" spindle washer
- Shop: Washer For 1" Spindle
- Shop: Spindle Nut, 1-1/2"
- Q&A: How To Fix the Cotter Pin Not Catching the Ears On Spindle Nut For a Boat Trailer
- Video: Let’s Check Out the Washer For 1" Spindle
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Finding the Right Trailer Wiring Harness
- Shop: Trailer Hitch
- Search Results: trailer lights
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Measuring To Choose The Right Trailer Axle
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Search Results: trailer jack
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Search Results: spare tire mount
- Article: How to Measure for Trailer Hitch Drop
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between Load Range B and C Trailer Tires
- Search Results: trailer wiring
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
on Trailer Bearings Races Seals Caps
