Loose Fulton Magnum Series Swivel Trailer Jack on 2002 Ranger Boat Trailer
Products Featured in This Question
Question:
I have a Fulton jack that has become to loose between the trailer mount and the jack mount. These to pieces are connected by nut and bolt, 2 cup washers and a lock washer. There is to much slop even when the bolt and nut is tighten all the way down. Do you sell replacement parts or a direct replacement jack? Thanks
asked by: Andy W
Helpful Expert Reply:
Your best bet is going to be hardware kit # F0933325S00. The bolt is a 1/2 inch coarse threaded bolt with matching nut and bushing. But it sounds like the nut or bolt is backing out on your assembly. This could mean the lock washer is shot. You could obtain one locally or use some blue Loctite # LT37643 to prevent it from backing out.
Do you notice any damage to the assembly? Or is the hole where the bolt goes through starting to get egg-shaped or otherwise misshapen? If so then that would be the issue and the mount would need to be replaced.
Replacement parts for the Magnum series jacks are not available so the best option we would have for that is # P9012-00.
Product Page this Question was Asked From
Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs
- Trailer Jack
- Boat Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Marine Grade
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Weld-On
- With Wheel
- Fulton
more information >
Continue Researching
- Shop: Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs
- Video: In-Depth Review of the Fulton Boat Trailer Jack w/ Wheel
- Video: Complete Breakdown of the Fulton Boat Trailer Jack w/ Wheel
- Q&A: Replacement Jack for Bulldog BD154107
- Q&A: Replacing Fulton Trailer Jack on 2004 Boat Trailer
- Shop: Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K
- Shop: Replacement Hardware Kit for Fulton Swivel Jacks
- Video: Ultimate Overview of the Jack Mounting Bracket for Fulton Marine Jack
- Shop: Jack Mounting Bracket for Fulton Marine Jack - Weld-On
- Q&A: Replacement Trailer Jack to Fit the Mount for a Shelby 5658A Swivel Jack
- Video: Checking Out the Replacement Hardware Kit for Fulton Swivel Jacks
- Shop: Bulldog Round Jack - No Mount - Topwind - 10" Lift - 2,000 lbs
- Q&A: Replacement Trailer Jack for Viking Legend Pop-Up Camper
- Q&A: Replacement Side Frame Mount Jack for Pop-Up Camper
- Shop: Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - 1.2K
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - 1.2K
- Search Results: fulton f2 jack
- Q&A: Recommended Replacement for Fulton Magnum Series Trailer Jack
- Q&A: Recommended Replacement Jack For Older Fulton Magnum 12000lb Trailer Jack
- Search Results: fulton f2
- Video: Pull Pin, Easy Swivel Trailer Jack with 8" Wheel: The Breakdown
- Search Results: adapter plate
- Search Results: fulton trailer jack
- Search Results: jack
- Search Results: trailer jack
- Search Results: fulton
- Article: Trailer Wiring Diagrams
- Video: etrailer Electric A-Frame Trailer Jack Detailed Breakdown
- Shop: Trailer Hitch
- Article: How to Measure for Trailer Hitch Drop
on Trailer Jack
Steve C.
5/27/2020
I want to replace my 1997, 27 yr old Fulton jack. It is welded onto a Brunswick Marine (Procraft) single axel trailer. It mounts to the welded plate with a center bolt. The distance from the center bolt to the lock pin hole is about 3 & 3/16 inches. It is probably a 1,200 lb jack. Do you have a current jack that will work with the existing welded bracket?