Customers compare 84557UC3 to these similar products
Products Featured in this Video
Hi, everybody. Andy here with etrailer.com. Let's take a look together at this Dexter pre grease trailer hub and drum assembly. Now this trailer hub and drum assembly is going to fit your 3,500-pound axle with an 80 number 84 spindle. And this is going to be compatible with electric and hydraulic drum brakes. And it comes pre grease with Dexter grease with the bearings and the seal… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The definitive way to determine the correct replacement hub is to go by the inner and outer bearing numbers stamped into the sides of the bearings. With these numbers I can determine the best hub or hub and drum assembly for your trailer. Trailer Hub…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…
view full answer...To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
view full answer...To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
view full answer...A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…
view full answer...I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…
view full answer...The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…
view full answer...For replacement Dexter manual adjust brake assemblies to replace your 36-19 you would want the part #23-27 for the right hand side and part #23-26 for the left hand side. These are manual adjust 10 by 2-1/4 inch Dexter brake assemblies that would…
view full answer...The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…
view full answer...Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…
view full answer...There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…
view full answer...