Replacement Hub for a UFP H-1377 on a 2004 Tahoe Boat Trailer

Question

Question:

Do you have a cross reference for a Ufp h-1377 p261 I need a total hub and bearing kit. It’s a 2004 Tahoe boat trailer

asked by: Stephen A

0

Expert Reply:

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing # L68149 and an outer bearing # L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com # AKIHUB-545-35-G-EZ-K. This is galvanized and will be the best option available for your trailer. This also includes both the inner and outer bearings, the grease seal, the grease cap, and the lug nuts.

expert reply by: Lazer S

0

John S.

6/3/2024

I am needing a pair of h-1377 hubs and bearing kit for my 2001 trailstar boat trailer

Reply

Lazer S.

6/3/2024

@JohnS Dexter Axle purchased UFP a while back and it looks like # 84545BX is the closest they/we have to a direct replacement, though not exactly the same. However, I would still go with our # AKIHUB-545-35-G-EZ-K as it is galvanized for better protection and will match the bearings (included) and bolt pattern. Plus it's less expensive, which is always a good thing.

Reply

Alton W.

1/1/2025

@LazerS I don't believe this is the correct answer. I also am looking for the same UFP H-1377 part number replacement. Inner and outer bearings are the same on mine, the L68149 bearing is used inner and outer on mine and is clearly stamped UFP H-1377. I am needing a set. I would also add these are oil bath hubs on mine. I don't necessarily need to go back with oil bath, and prefer not to.

Reply

Bryce D.

1/2/2025

@AltonW Unfortunately Alton, Lazer (yes that's his real name) is correct. Dexter did purchase UFP a while ago and the closest replacement we have Dexter Trailer Idler Hub Assembly for 3,500-lb Axles # 84545BX. You could also use the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles # AKIHUB-545-35-G-EZ-K like Lazer mentions, which is a bit cheaper.

Reply

Answer 1

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 2

I'm sure we can get you a pre-greased hub assembly to replace your UFP H1377, but I was unable to find any definitive information on exactly what will replace this hub. So in order to find the correct hubs you will need to take apart your current…

view full answer...

Answer 3

First, it does sound like, based on the measurement and information you have provided, that race #L68110, is correct since its outer diameter is 2.327 inches. This race is associated with bearing #L68149 which has an inner diameter of 1.378 inches…

view full answer...

Answer 4

Being off as little as it is, the hub may just be getting caught on something. Remove the hub from the spindle to make sure there is nothing that could be catching the inner bearing. Next, install just the inner bearing #L68149 making sure it gets…

view full answer...

Answer 5

I can help you pick out the correct hub, but we don't have a cross-reference part number for the one you listed. In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first…

view full answer...

Answer 6

The UFP H-1377 is for a #84 spindle. This will use the Bearing Kit #BK2-100 or the Easy Grease Trailer Idler Hub Assembly #AKIHUB-545-35-G-EZ-K if you wish to have a all new hub. I recommend using the Grease #L11390 with the bearings or hub. This…

view full answer...

Answer 7

Thanks for the pictures! I would be happy to help you find the correct replacement hub for your trailer, but I need some more information. You will need to determine which inner and outer bearings your spindle uses as I was unable to find any…

view full answer...

Answer 8

Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing #L68149 (Inner diameter…

view full answer...

Answer 9

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

I do see many of the 2009 Ranger Trail trailers allow you to use a replacement Inner Member. You will need to match these with your specific actuator and either Disc #DX99FR or Drum #DX97FR brakes. If you can tell me exactly what model number…

view full answer...

Answer 12

Dexter doesn't put reverse lock outs on their drum brake actuators so you'd need to add the part #DM5404 do a new actuator. The part #DX97FR is just the inner section of an actuator though. For the actuator you'd need the part #DX33FR.

view full answer...

Replacement Hub for a UFP H-1377 on a 2004 Tahoe Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching