Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly -…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
I&…
If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Ford E-Series Cutaway AccessoriesSelect A Category Below
Towing
Ford E-Series Cutaway Trailer Wiring
Ford E-Series Cutaway Brake Controller
Ford E-Series Cutaway Front Mount Hitch
Ford E-Series Cutaway Towing Mirrors
Ford E-Series Cutaway BOLT brand vehicle and hitch locks
Cargo Control
Ford E-Series Cutaway Roof Rack
Performance Accessories
Ford E-Series Cutaway Air Filter
Ford E-Series Cutaway Suspension Enhancement
Ford E-Series Cutaway Vehicle Lights
Ford E-Series Cutaway Tire Chains
Ford E-Series Cutaway Fluid Filters
Ford E-Series Cutaway Vehicle Sway Bars
Ford E-Series Cutaway Vehicle Engine Heaters
Vehicle Trim
Ford E-Series Cutaway Floor Mats
Ford E-Series Cutaway Nerf Bars - Running Boards
Ford E-Series Cutaway Bug Shield
Ford E-Series Cutaway Side Window Vents
Ford E-Series Cutaway Mud Flaps
Ford E-Series Cutaway Lamp Guards
Ford E-Series Cutaway Vehicle Seat Covers
Ford E-Series Cutaway Windshield Wiper Blades
Ford E-Series Cutaway Battery Box Relocation
Ford E-Series Cutaway Windshield Covers