Separate wiring system - brake and turn signals are sent along separate wires. A converter is required unless the vehicle is equipped with a tow package plug. The tow package plug has already been converted.
Custom Fit Vehicle Wiring Specs:
Features:
This socket plugs into T-connector to provide a 7-pole trailer connector in the truck bed for use with fifth wheels. Connector plugs into OEM wiring harness to allow for a 7-pole connector in the truck bed.
More Information >Trailer Wiring Specs:
Features:
This 7-pole, sealed, RV-style trailer connector plugs into the factory socket on your truck or SUV. Connector is an exact OE replacement on Chevy, Ford, GMC and Nissan.
More Information >Custom Fit Vehicle Wiring Specs:
Features:
This socket is designed to fit into a pre-existing cutout on 2007-2013 GM 1500 trucks and 2007-2014 GM 2500/3500 trucks. Twist-in connector also serves as a replacement for OEM sockets on GM trucks 1999-2013 that came with factory tow packages.
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Mount this 7-way, RV-style connector in your truck bed to simplify hookup of your 5th-wheel or gooseneck trailer. Harness plugs into existing wiring and retains use of factory 7-pole at the bumper. 90-Degree connector fits into tight spaces.
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light…
view full answer...If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.
view full answer...Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…
view full answer...Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...