How To Choose the Correct Replacement Landing Gear Motor

Question

Question:

Need motor for my Landing gears.

asked by: Lori

0

Expert Reply:

The replacement landing gear motors are all pretty much the same so you shouldn't have too many issues finding a compatible replacement. However, if you have a dual landing gear motor setup and you will only be replacing one of them then you will need to match the exact RPM rating on the motor you have now or just replace them both. The correct replacement for you should be the Replacement Motor for Electric Landing Gear part # LG-142178 which has a standard 5,500 RPM rating.

expert reply by: Conner L

0

Answer 1

Sounds like you have tried manually operating the jacks and they work fine, so the jacks are not the problem. The gearbox is in good working order too. That leaves the motor. An optional motor can be added to this jack, part #LG-142178, but note this…

view full answer...

Answer 2

I don't have any way of determining if the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-HDL will work with your 2007 Fleetwood Nitrous Hyperlite TT Toy Hauler or not, unfortunately. The Replacement Crank Handle…

view full answer...

Answer 3

Yes, based on the distance between the welded on brackets of your camper the etrailer landing gear set part #RVLG-8HDL will fit on your 2021 Forest River Cherokee Wolf Pack. The motor normally used with this kit is the part #LC142178. If the motor…

view full answer...

Answer 4

Other than the clicking sound is the landing gear functioning properly? Usually, when someone says they have clicking the jacks are either working slowly or not at all. Check the connection of the ground wire on the motor and make sure it's…

view full answer...

Answer 5

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 6

The replacement motor for your landing gear is #LG-142178.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Bobby! As far as the jacks go for item #RVLG-8000 and item #RVLG-8HDL there is absolutely nothing different. The item #RVLG-8HDL comes with the manual handle that I have attached a picture of below. That is the only difference. If your 2019…

view full answer...

Answer 9

Hey Bob, Landing gear components aren't all interchangeable between brands so I'd need to know the exact model to find replacement parts for your current system. If you're just wanting to replace the landing gear as a whole then I'll…

view full answer...

Answer 10

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your end.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

How To Choose the Correct Replacement Landing Gear Motor

Product Page this Question was Asked From

Continue Researching