Amperage Draw of Optronics Sealed Mini LED Side Marker Lamp # MCL13A2B

Question

Question:

I purchased product MCL13A2B. How many amps does it draw and do you have a recommendation for the appropriate gauge wire to use? Thanks

asked by: John

1

Helpful Expert Reply:

The Optronics # MCL13A2B Sealed Mini LED Side Marker lamp draws 0.046 amps at 12.8 volts. I'd recommend using 16-18 gauge wire for your trailer lighting circuits. If you're rewiring your trailer, we carry a bonded 3-wire, part # 16-3B-1 which is sold by the foot.

I'll link you to our help article about trailer wiring, which I hope you'll find helpful.

expert reply by: Mike L

1

Answer 1

If your existing lights have mounting holes that are 2 inches apart from the center of the holes, then the Optronics LED Side Marker #MCL13A2B would work just fine as a replacement.

view full answer...

Answer 2

In order to splice into the wire and add yellow side marker lights like the #MCL13A2B I recommend using the Self-Stripping Connector with Waterproof Sealant #SWC501746-1. This is designed to make a quick connection without cutting or stripping, and…

view full answer...

Answer 3

The polished chrome ring, #A13C2B, is not required for mounting the sealed mini side marker lights, #MCL13A2B and #MCL13R2B. This is decorative trim ring only. The foam gasket, #A13G2B, would be used if these lights are mounted on the outside of an…

view full answer...

Answer 4

Hi Jeong-Won; the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX89FR fits a 3" wide trailer tongue without a specific height requirement. To add a hinge back onto the tongue you simply have to measure the height. If you have a 3"…

view full answer...

Answer 5

All of the Replacement Round Spring Bars for the Fastway e2 Weight Distribution systems, #FA94-02-1099, #FA94-02-0899, and #FA94-02-0699, measure 31-1/2 inches long. The diameter of the bar at the upper end is 1.39 inches, and the inside groove…

view full answer...

Answer 6

Hey Eric, The hitch extenders that we currently offer for a 2-1/2" receiver tube opening unfortunately max out at 6,000lbs GTW and wouldn't be capable of towing the trailer. You're most likely going to need to upgrade to a TorkLift…

view full answer...

Answer 7

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 8

Hi Marcus! The Taskmaster Modular Wheel w/ +0.08 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Silver #TA35ZR weighs a hair over 51 pounds. Pretty heavy, but it is a pretty heavy duty wheel. Do you already have a tire picked out for this? It…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Amperage Draw of Optronics Sealed Mini LED Side Marker Lamp # MCL13A2B

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching