Recommended Hitch and Trailer Wiring for a 2026 Jeep Wrangler
Updated 11/16/2026 | Published 11/14/2026 >
Products Featured in This Question
Question:
I just purchased 2026 wrangler. It got wired for flat towing. I want to add a receiver and trailer light plug. Will there be a pig tail for me to plug into from the wire loom they installed or will I need to splice into the wires?
asked by: Richard W
Expert Reply:
Welcome back Richard and congrats on the new Jeep. To add a hitch and trailer lighting to a 2026 Jeep Wrangler, I recommend the Curt item # C13392 and item # 56407. There will not be a anything in your flat tow wiring harness for you to plug directly into but you won't need one or have to splice wires.
The Curt item # 56407 trailer wiring plugs directly into your Jeep's factory wiring behind the tail lights. It'll provide you with a 4-way connector that is capable of controlling your trailer or accessories lighting functions. It is compatible with the Curt Custom Tail Light Wiring Kit item # C96JR you were looking at. I didn't see any order information so I am not sure if that's the one you had installed.
The Curt item # C13392 is a custom fit class III hitch with a 2" receiver. It has a super simple installation method that only requires you to install four bolts in your rear bumper. The bolts needed to complete the installation are included as well.
What do you plan on using your new hitch for? Feel free to answer this and throw in any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Step-By-Step Install Curt Custom Tail Light Wiring Kit - 2026 Jeep Wrangler Unlimited
- Shop: Nerf Bars - Running Boards
- Shop: Trailer Wiring
- Shop: Westin Outlaw Nerf Bars with Drop Steps - Textured Black Steel
- Video: Roadmaster Smart Diode Kit Installation Guide - 2026 Jeep Wrangler Unlimited
- Shop: Vehicle Tow Bar Wiring
- Shop: Curt Custom Tail Light Wiring Kit for Towed Vehicles
- Video: Installing the Curt Trailer Hitch Receiver on a 2026 Jeep Wrangler
- Q&A: Does the Curt Custom Tail Light Wiring Kit C96JR Include Diodes?
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Review of the Curt Custom Tail Light Wiring Kit for Towed Vehicles
- Shop: USB Remote Power Cable for Blue Ox Patriot Flat Tow Brake Systems
- Shop: Replacement 12-Volt DC Power Cord for Voyager WiSight 2.0 Wireless RV Backup Camera System
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer jack
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown





Andy V.
11/16/2026
I had a slightly different approach to installing the "T" harness on my 26 Jeep JL Sport S. For me the right hand side was a bit short for the way I wanted to route the wiring. After custom lengthening that side of the harness and fishing it across the back of the jeep and up into the Tail lamp pocket, the 12V power wire was covered in red 1/4 split loom for easy identification that it is a HOT lead. Fishing through the chassis, over the rear wheel area and alongside/topside of the frame rail attaching with zip ties, then up to the battery area from the bottom of the body. The Curt hitch itself, the 5K unit was heavy duty, hardware was great, and easily feed through the existing holes. I did not enlarge the holes as outlined, simply put some fabricators wax on the threads and spun them in. No harm to threads at all... MY connector for the trailer is on the right hand side of the hitch. a 12" extension was needed to do this.