Where Does the Voyager PWM Filter for RV Camera Systems part # VGR74VR Install?
Updated 07/20/2026 | Published 07/14/2026
Products Featured in This Question
Question:
I have a 2026 airstream with a 7-pin connector connected to my 7 pin 2026 GMC Sierra. I do not see how to connect this PWM filter without cutting wires. Is there a video or picture showing when each end plugs in?
asked by: Kirk O
Expert Reply:
Hi Kirk,
The Voyager PWM Filter for Voyager RV Camera System part # VGR74VR doesn't install into your vehicle or RV's 7-way. This connector needs to be installed between the factory Voyager camera wiring and the camera itself. You can do this by removing the mounting plate or camera from the rear of the RV and unplugging the factory CEC connector. Once you've done that you plug the VGR74VR into the factory CEC connector and plug the camera into the other end of the VGR74VR, then reinstall the camera. If your RV isn't prewired with the Voyager CEC connector, then you need to use the hardwire version, Voyager 12V PWM Filter for RV Backup Camera Systems part # VGR64VR. To install the VGR64VR you'll need to cut the power and ground wires to the camera and splice in power (red wire) and ground (black wire) from the PWM filter using the included butt connectors. From there secure the filter inside the wall with zip ties so it doesn't move around and reinstall the camera.
Did your new Airstream come with a factory Voyager camera system?
Product Page this Question was Asked From
Voyager PWM Filter for Voyager RV Camera Systems - CEC Connector
- Accessories and Parts
- RV Camera System
- Pulse Width Modulator Filter
- Voyager
more information >
Continue Researching
- Search Results: trash can
- Q&A: Why Is My Prewired RV Camera Not Pairing With The Voyager WiSight 2.0 Monitor?
- Shop: Topargee Flush-Mounted Fresh Water Tank Gauge w/ Adapter Fittings
- Search Results: happijac
- Shop: 7-Way Vehicle Power Adapter for Furrion RV Observation Camera
- Shop: Voyager Rear Camera with LED Low Light Assist - Black
- Shop: Voyager PWM Filter for Voyager RV Camera Systems - CEC Connector
- Shop: Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for Prewired RVs - 7" Screen
- Shop: 12V PWM Filter for RV Backup Camera Systems - Hardwire
- Shop: Replacement Voyager WiSight 2.0 Wireless RV Backup Camera with Low Light Assist
- Q&A: Will the Voyager WiSight 2.0 Wireless Backup Camera System Work w/a Pre-Wired Travel Trailer?
- Q&A: Permanent PWM Filter for 2024 Ford F-250 and Furrion Vision S Camera System
- Q&A: Correct Backup Camera System for a Coachmen Apex Ultra Lite
- Q&A: Is The 2022 Winnebago Micro Minnie 1700BH Prepped For a Voyager WiSight 1.0 or 2.0?
- Q&A: Troubleshooting A Voyager WiSight 2.0 Camera System That Won't Pair
- Q&A: Correct Voyager WiSight Camera for Installation on a 2022 Winnebago Prewired for Voyager Camera
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Shop: Gooseneck Hitch
on Accessories and Parts
Kirk O.
7/18/2026
Yes my 2026 airstream came with voyage rear camera installed. Not sure when I remove the small rear camera assembly IF there will be room to add this 12 inch piece and shove it back into the airstream frame? Is there a video if this camera take down and CEC install. I don’t am not sure IF I have a CEC plug and play camera until I contact airstream. Thanks for reply Kirk