Hubs and Brakes for 2k Axle
Updated 07/10/2026 | Published 07/02/2026
Products Featured in This Question
Question:
Im converting a small trailer brake system from Disc to Electric Drum. I have a 7 x 11/4 electric brake system in my shopping cart. Along with 7 4 on 4 Drums. How do I know if the bearings will fit the axle? Are they a standard size for a 2000 to 2500lbs axle?
asked by: Glenn B
Expert Reply:
Hey Glenn! There are two standards for 2k spindles. The Dexter Trailer Hub and Drum Assembly # 8-173-16UC3-EZ uses # L44649 inner and outer bearings with an inside diameter of 1.063". If you have # L44643 bearings with a 1.00" ID the only option we have is the # AKHD-545-2-EZ-1K which has a 5 on 4-1/2 bolt pattern instead of a 4 on 4. Both are compatible with the etrailer Electric Trailer Brakes # AKEBRK-2.
If you aren't sure about your bearings, you will either need to pull the hubs and measure, or identify it using the axle tag. If it is a Lippert or Dexter axle they can identify the bearings using the serial number. You will also need to add a 7-way like # e99011 and run some additional wire # 10-1-1 to complete the conversion.
What kind of trailer are you working on?
(click to enlarge)
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly for 2,200-lb E-Z Lube Axles - 7" Diameter - 4 on 4
- Trailer Hubs and Drums
- Hub with Drum
- EZ Lube
- L44649 / L44649
- Standard Grade
- For 2200 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: brakerite
- Search Results: trailer hubs and drums
- Search Results: brake drums
- Shop: Dexter Trailer Hub and Drum Assembly for 2,200-lb E-Z Lube Axles - 7" Diameter - 4 on 4
- Shop: Trailer 4 on 4 Hub & Drum Assembly - 2,200 lbs. Axles - Hydraulic Brakes
- Shop: Trailer Hub and Drum Assembly - 2K Axles - 7" Diameter - 5 on 4-1/2 - L44649 - Pre-Greased
- Shop: etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 2,200-lb Axles - 7" Diameter - 4 on 4
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Shop: Dexter Trailer Hub and Drum Assembly for Hydraulic Brakes - 2,200-lb Axles - 4 on 4
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Suspension Enhancement
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Q&A: Who Makes The Best Quality Trailer Bearings?
- Search Results: trailer jack
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: How to Measure to Determine the Size Trailer Brakes Needed For Hydraulic Drum Replacement
on Trailer Hubs and Drums
Glenn B.
7/9/2026
Thank you for your reply. I'm converting a camper trailer I'll be pulling with my motorcycle. The trailer came with Electric over Hydraulic Disk Brakes powered by a Brake Rite actuator. The actuator has failed and a replacement is too expensive. I currently pull a Timeout camper that has electric brakes, so my bike is already setup for this kind off system. I already ordered the Brake Drums that have the L44643 bearings under an assumption they are standardized. Should the bearings not be the right size can they be removed and replaced with the corrected ones? I have the means to do the required work provided the outer race is the same.