Is B&W Anti-Rattle Clamp Compatible With Andersen Weight Distribution Hitch

Question

Question:

Would the BandW Anti-Rattle Clamp for 2-1/2inch Hitch Receivers Part Number: BW65FR work with Andersen weight distribution system?

asked by: Markell H

0

Expert Reply:

Hey Markell! The B&W Anti-Rattle Clamp for 2-1/2" Hitch Receivers # BW65FR is not compatible with any weight distribution hitch so it can't be used with the Andersen.

With that gusset welded on the shank I recommend the Roadmaster Quiet Hitch for 2-1/2" Trailer Hitches # RM-062 instead. This doesn't have a weight distribution restriction and will be compatible with the design of the Andersen.

What kind of trailer are you towing?

expert reply by: Robin H

0

Roadmaster Quiet Hitch
(click to enlarge)

Markell H.

7/1/2026

Grand Designs 2800BH pulling with a ‘20 Ram 2500

Robin H.

7/1/2026

@MarkellH thanks! That'll be a great setup. The # RM-062 will work well with your Andersen and the factory 2-1/2" receiver on your Ram 2500.

Markell H.

7/10/2026

@RobinH I had to install the anti-rattle upside down, through the chain loop (I assume that’s ok??). Per the instructions, it’s this can be done for more ground clearance. The factory Ram receiver is very short. Set up will be tested today

Robin H.

7/10/2026

@MarkellH it is perfectly acceptable to install it upside down, not a problem.

See All (5) Replies to Markell H. ∨

Answer 1

Yes, the Atwood carbon monoxide detector part #AT36681 replace the 33535E that you have now.

view full answer...

Answer 2

Hey Joe, welcome back! How much power draw does your cooler have? The circuits that power your 7-ways are often fused with a 30 amp fuse/relay. The factory and aftermarket options like item #C57010 are ran off of the same circuit. You'll want to…

view full answer...

Answer 3

Yes, you can use the Equal-i-zer Weight Dist Shank #EQ90-02-4600 with a Reducer Sleeve #325-GH-007 on your 2022 Ram 2500. I do highly recommend using a Roadmaster Quiet Hitch #RM-062 to remove the excess play from the receiver to the hitch. Having…

view full answer...

Answer 4

The Andersen Rapid Hitch Adjustable Ball Mount #AM3410 that you referenced is an excellent product that's designed to fit securely into a 2 inch hitch receiver. I can't give an honest assessment on how this compares to the unit you purchased…

view full answer...

Answer 5

Good question, Dan. Though there are options available that can be used with weight distribution systems (like the Roadmaster #RM-061), the etrailer #e38FV should not be used. The extreme loads that are associated with engaged weight distribution at…

view full answer...

Answer 6

Yes, it will David so long as you're using a 2-1/2" hitch to 2" hitch adapter like item #e53YR. The Blue Ox Hitch Receiver Immobilizer III item #BX88312 is only designed to be used with a 2-1/2" hitch and shank of 2" hitch…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is B&W Anti-Rattle Clamp Compatible With Andersen Weight Distribution Hitch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching