How Far Apart Should E Tracks Be Installed On a Motorcycle Trailer

Question

Question:

How far apart should e track be for a one bike trailer?

asked by: Scott H

0

Expert Reply:

There's not a set distance that the E-Tracks like part # E19148 should be apart when installing in a one bike trailer. That will depend on the trailer dimensions, the weight of the trailer and where the best mounting locations are in your trailer. Are you planning on installing them on the floor or the walls? I am assuming it's a motorcycle trailer. If you are using wheel chocks, I would recommend putting the E-Tracks a couple feet on either side if possible. You don't need an exact figure but close enough that the tie downs are pulling down, and far enough apart to provide side-to-side stability. This will depend on the width of your handle bars as well.

You might also be interested in the E-Track D-Ring part # E59143 and the Tie Down Kit part # EM34410.

expert reply by: Jameson C

0

Answer 1

Since the slot dimensions and capacity of different brands of E-Track are identical, really the only differences are the finish and the lengths the tracks are sold in. If you're using the E-Track in an area where aesthetics are important, you can…

view full answer...

Answer 2

Basically you'll have to mock up where you want the motorcycle to be and where the best place will be for the e-track as there isn't a set place to install the tracks in every trailer. Typically you want the tie down anchors to be about 36…

view full answer...

Answer 3

If you used wood screws in every hole of the E-track part #EM59150 that you referenced you'd have enough capacity to secure your 900 lb motorcycle. There isn't a one-size-fits-all method for installing the E-tracks but for your situation and…

view full answer...

Answer 4

Yes, you can use wood screws to secure the e-tracks to the plywood walls in your trailer. However, as you mentioned the weight capacity would be less than if you were to attach them to metal beams. The tracks themselves can handle up to 2,000 lbs but…

view full answer...

Answer 5

For a trailer tire, the narrowest option rim for any given tire is going to be the best option. For a 205/75-15, the best option would be a 5 inch rim. The reason that narrower is better is because it provides more support for the tire. Since trailer…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How Far Apart Should E Tracks Be Installed On a Motorcycle Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching