Replacement Jack for Fulton F2 2000 lbs Jack With Foot

Question

Question:

I have a Fulton f2 2000lb jack with the foot. I broke the top plastic piece that encases the handle. Do you have any parts available? Do you have contact information for them? I’ve sent horizon several emails with no response What do you have that’s similar to the f2? I have very low ground clearance. About 8”

asked by: Brian B

0

Expert Reply:

Hey Brian,

I'm sorry about the issues with your jack. I totally understand how that can put you in a bind. Horizon Global brands are no longer in production, so the replacement parts for Fulton are no longer available. That would also explain why you haven't received a reply yet. Instead, you can go with Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs # e74VV. The retracted height on this jack is 7-1/8", so it'll stay clear and won't drag on the ground and this one is rated for up to 3,000 lbs, so it will be higher rated for you than the Fulton F2. We have many replacement parts for our etrailer jacks, so you won't have to worry about being able to find those parts! What kind of trailer are these parts going on?

expert reply by: Jerry B

0

Brian B.

6/30/2026

This is for my boat tracker targa dual axle trailer 3000lb is probably way more than I need. 1500lb should be plenty

Jerry B.

6/30/2026

@BrianB Understood! I did some more looking but this was the only one I was able to find that will give you the 8" clearance. Alternatively, you could go with a swivel jack like Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate - Sidewind - 14" Lift - 1.6K # TV64FR to turn 90 degrees the sit parallel to your trailer's frame.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Hello Kayla, I am so glad you wrote in to us! I was able to confirm with MCD Innovations that you will need the MCD Innovations RV Shade Repair Kit - Solo with Steel Brackets - Switch Controlled Motor #MC82YR to replace your current motor…

view full answer...

Replacement Jack for Fulton F2 2000 lbs Jack With Foot

Product Page this Question was Asked From

Continue Researching