Recommended MaxxFan Deluxe Roof Vent w/a Thermostat

Question

Question:

Looking for maxair fans with themsate and 50 amp trailer plug and part that goes threw trailer wall thanks

asked by: Randy S

0

Expert Reply:

Hey Randy. I recommend the MaxxFan Deluxe Roof Vent item # MA00-07000K. This would be a great option due to it having a 10 fan speed settings, a powered lifting lid, and a thermostat that will keep your RV to the temperature you set. The included remote will allow you to completely control the fan settings and adjust the thermostat.

I also recommend using the Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White item # 344270KITW to make sure you have a leak free install.

For a 50 amp trailer plug that installs in your RV's wall, you'll want the Mighty Cord Replacement RV Power Inlet item # A10-50INBKVP in black or item # A10-50INVP in white. These are 50-amp twist-lock male plugs that have a dust cover and polyester construction for all weather resistance.

What kind of trailer or motorhome do you have?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

A10-50INBKVP
(click to enlarge)

MA00-07000K
(click to enlarge)

Randy S.

6/9/2026

Ok thanks for your help

Jerred H.

6/9/2026

@RandyS You're welcome!

Doug S.

6/10/2026

Super quiet, 10 speeds, remote is handy. Et the full rain hood one, then no worries if it rains if you are away. Since I replaced a non powered vent, had to use some self adhesive plastic wire mold with molded corner covers which came out looking very clean. The inside trim mold is pretty easy to fit to the roof thickness, great vent for over the kitchen.

Don H.

6/11/2026

I've installed 3 MaxxFan Deluxe in Chevy vans over the years. We haul hunting retrievers to AKC events so their good health is a prime concern. Always been pleased with the fans performance. We're not real good at checking battery status in the remote so having the little control panel in the fan shroud can keep the fan running when you need it. Never had rain get into the fan so it's well designed. I'm a repeat buyer. Nuff said.

Jerred H.

6/11/2026

@DonH Thank you so much for sharing that feedback Don! I appreciate you taking the time to share your story.

Answer 1

In order to replace torsion axles with leaf spring axles you'll first need to start with a hanger kit, if it's a tandem axle trailer then I recommend the Tandem-Axle Trailer Hanger Kit for Double Eye Springs part #APT5. This can then be…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended MaxxFan Deluxe Roof Vent w/a Thermostat

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching