Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White
(207 reviews)
Price: $60.71
Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White
Item # 344270KITW
Our Price: $60.71
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (207)
- Q & A (0)
- Photos
LaSalle Bristol Accessories and Parts - 344270KITW
- RV Vents and Fans
- Vent Install Kit
- LaSalle Bristol
Roof vent install kit allows you to properly mount your RV roof vent and create a waterproof seal. Kit includes 2 tubes of self-leveling sealant, 1 roll of butyl tape, 8 wood screws, and 30 sheet metal screws.
Features:
- Installation kit includes everything you need to mount your RV roof vent with a waterproof seal
- Works on surfaces such as aluminum, brass, steel, glass, mortar, wood, PVC, EPDM, TPO, and TPV
- Pre-formed, synthetic polymer butyl tape remains flexible for years
- Adhesion improves with age
- Weather-resistant, paintable sealant is self-leveling for horizontal surfaces
- No primer required
- White color
- Kit includes:
- (2) 10.1 oz tubes of sealant
- (1) 30' Roll of butyl tape
- (8) #8 x 3/4" wood screws
- (30) #8 x 3/4" sheet metal screws
344270KITW Roof Vent Installation Kit - RV Roof Membrane - Sealant, Butyl Tape, Screws - White
31071 Zinc Sheet Metal Screw - 8 x 3/4" Indented Hex Washer Head - Hex Slotted Drive
30587 Wood Screw - 8 x 3/4" Slotted Round Head
270341410B LaSalle Bristol XTRM Butyl Tape - 30' Long x 3/4" Wide - Qty 1
27034145 LaSalleBristol XTRM Universal Self-Leveling Sealant - 10.1 oz - White - Qty 24
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Arrived Damaged
Customer Reviews
Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White - 344270KITW
Average Customer Rating: 4.6 out of 5 stars (207 Customer Reviews)
Roof vent install kit allows you to properly mount your RV roof vent and create a waterproof seal. Kit includes 2 tubes of self-leveling sealant, 1 roll of butyl tape, 8 wood screws, and 30 sheet metal screws.by: Gary05/09/2023
I bought this kit to make my roof vent install water tight. The butyl tape and self leveling sealant were exactly what was needed. The kit comes with two sets of screws (which weren’t included with the roof vent), however I didn’t use them as one set was slotted (flathead vice Phillips) and the other (better) were hex head/slotted. I prefer Robertson (square drive) screws and that is what is stock on this trailer so that’s what I used. I would have given 5 stars if the screws that came with the kit were better quality (i.e. weren’t slotted). Regardless, there is no doubt it is water tight. Good kit.
by: Troy 11/20/2023
Exactly what I needed. Replaced roof vent on my 1964 Shasta and the self leveling sealant worked just as described. I applied it when temperatures were in the 50s and nights got down to the 30s so it took a couple days to dry. I’ve had no issues at all.
by: Gary08/26/2023
I gave this order 3 stars because whoever shipped this order put the vent and the installation kit in the same box. The roll of tape was damaged, but I think everything else look okay. I have read other reviews saying the same things I encountered happening and somebody is not paying attention to these reviews. Also the plastic piece of the vent should of been packaged better as they were laid in there to flop around. I am surprised that nothing else was damageed. etrailer is better than this I would think.
by: John09/08/2023
Used to seal the replacement roof vent (old one was damaged from tornado). Followed instructions. Took our time and installation went well in 73 Deg weather. After a year, sealant is still good. (Trailer is stored under open sided shelter).
by: Jorge 11/03/2023
What I'd like to know is how ETrailer got my Roof Vent stuff to me so quickly. Not only that, but I get a note right after I ordered referencing a prior order (for the same thing...different trailer) and I'm saying to myself, "These folks take customer service to another level." Everything ordered was in the box and delivered intact.
by: Carl05/17/2023
1Here are some pics of the way my order was recieved
Jenny N.
5/22/2023
It does look a bit rough around the edges. I will have our Customer Service team reach out to make sure that the kit was not damaged.
by: Daryl08/15/2023
This kit is mostly complete. The only thing missing is a guy to get up on the roof of my camper who can use a heat gun to soften all of the old sealant and yank out the old vent. Seriously, the kit has everything I’ll need to install the new vent.
by: Cindy05/04/2023
The roll of butyl tape I received was twisted and bent. I had enough to complete my job but had to throw about half of it away. I'm not sure on the sealant. After 7 hours it is still very, very, soft. (I don't know if that is normal). The mounting screws have slotted heads. Be much better if they were phillips-I ended up replacing the slotted screws with phillips.
Jenny N.
5/12/2023
I am sorry that the butyl tape arrived like that. I will have Customer Service reach out to you. The sealant should cure in an hour however if it is still soft then wait 24 hours if you plan to paint it.
by: Judi06/04/2023
the sealants were damaged the tape was fine, so I had to go to a hardware store to purchase two sealants luckily they sold same brand. But this is not etrailers fault I blame the transportation of it. I am more than pleased with etrailer and all the products we have purchased from you. your customer service is amazing! the knowledge of the staff is far beyond any other company.
Katrina B.
6/8/2023
Oh no! Lets get you over to our customer service department for them to get you some type of reimbursement.
by: Paul 10/14/2023
Fan as described. Installed with help of on line customer videos. Works well. Butyl tape arrived nearly folded in half but it worked ok.
by: Aaron 08/22/2023
Great kit, I was able to re-use the mounting screws that were a bit nicer than the ones with this kit. Adhesives worked perfectly.
by: Norm 04/06/2023
The kit is more than sufficient for a 14x14" vent fan installation…except for the exterior screws.
One tube of sealant was just almost enough, but a little more from the second tube finished the job. The sealant looks adequate so far. Time will tell how long it lasts and how well it works. I put two rows of butyl tape under the vent’s flange and there’s almost but not quite enough left over for a second installation.
The screws on the other hand are all zinc coated. Not ideal to be up on a roof, covered with sealant or not. Fortunately, my new vent fan came with stainless steel screws.
I would suggest eTrailer consider replacing this kit with two alternate versions: one without screws and one with stainless screws. Standard shipping arrived on the third day. The price seems a little stiff, but to have everything I needed packaged and ready to go…well, OK.
by: Dale 10/16/2023
Arrived in timely manner, included the stated items more than enough type and sealant to install one roof vent.
by: James 10/26/2023
Etrailer had excellent customer service !!
by: Donald 09/13/2023
Worked as expected - easy install and foolproof seal.
by: Mike 07/24/2023
Had vent installed in about 2 hours, inst.ablation kit worked great
by: Pamela 08/05/2023
I find e-Trailer to be both reliable and respectful. E-Trailer really is my "Go-To" for obtaining the items I need to improve and/or maintain my RV. Thank you.
by: Brian 10/14/2023
Gave me everything I needed to install the new roof vent. Good quality product and shipped quickly.
by: Jorge 06/30/2023
Delivery was earlier than expected and the materials ordered were in the box. I was able to find an installation video of this exact product online so I am ready to install. Of course today will top out at 98 degrees and tomorrow is looking more like 100...sigh...
by: Roe04/22/2023
Stop putting ordered loose items together in that long rectangle box! I have on caulking tube with a bent tip that may have punchered the seal , im not ready to use or test it yet so i don't know yet if it is any good. You cant blame the shipper , he doesn't know what loose in the box or which side is up . If I ever order anything it will only be ONE item at a time..P.S. same shipping issue last time I order a year ago... and it is the packer not the shipper.
by: Mark12/29/2022
I assumed this installation kit would be packaged separately from the roof vent, but instead all that stuff was just thrown in the box with vent. There was sealant that leaked on screen for the vent. Poor packaging job.
by: Gary03/07/2021
More than enough tape and caulking to install two 14" x 14" roof vents. Worked well.
by: Scott06/27/2023
Still holding and doing great, no leaks or anything. Easy to use and install
by: Martin 01/13/2023
Perfect add on for the vent I purchased. Everything I needed for a proper water tight installation was there, plus enough for another if I decide
by: Annabelle08/22/2023
Everything was great!
25
207
Show More Reviews
See what our Experts say about this LaSalle Bristol Accessories and Parts
- Can Roof Vent Install Kit 344270KITW Be Used on Cargo Trailer with Henry’s Tropic CoolYes the Roof Vent Installation Kit # 344270KITW can be used on a roof of a trailer that has had the Henry’s Tropic Cool installed.
view full answer... - Install Kit Recommendation for Trailer Roof Vent with SealantWe have the part # 344270KITW which includes hardware and sealant for installing a roof vent like what you mentioned. I attached an install video that covers how this is used as well.
view full answer...
- Will the Roof Vent Installation Kit 344270KITW Work On a Fiberglass Roof Yes, the Roof Vent Installation Kit part # 344270KITW will work just fine on a fiberglass roof. I verified this with the manufacturer of the sealer for you, LaSalle Bristol.
view full answer... - Ceiling Garnish Installation Kit for Ventline Ventadome Trailer Roof VentsThe ceiling garnash won't include screws but there is an installation kit for trailer roof vents. The kit # 344270KITW includes sealant, Butyl tape, and all screws needed for installation. The sealant can be painted 72 hours after setup. The types of screws included are sheet metal screws (30 count) and round-head wood screws (8 count). Garnishes are only available in white.
view full answer... - Drill or Clamp Fan-Tastic Roof Vent for RV and Tip for Cutting Garnish to LengthI like the more permanent drill application Fan-Tastic roof vents like the # FV801350 you referenced as they are easier to keep sealed. For an install kit the # 344270KITW would work well. This comes with the needed screws and all of the sealant you'd need. To trim the garnish I would recommend using masking tape to mark where you want it cut and then use a fine tooth saw to make the cut. Since it's plastic it will cut very easily.
view full answer... - Can Housing of Roof Vent Be Left In Place for Roof Vent InstallationYou could get away with keeping the same garnish (trim piece inside the cutout) but unless there are specific parts you're replacing on your roof vent you'll need to replace the entire unit with the Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat # FV802250. This is going to be the same case no matter what roof vent you have. Please note you need the Roof Vent Installation Kit # 344270KITW as well to get this vent installed. I'm attaching some review videos for you to also check out. If...
view full answer... - Recommended RV Roof Vent For A Trailer Bathroom The Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Powered Lift # FV803350 you were already looking at is going to be the best option for what you're looking for. It has a smoke lid to allow in light and built in rain sensor to automatically close the vent lid when rain is detected. The garnish ring can be trimmed down to fit your 1" thick roof, you'll just want to also pick up the Roof Vent Installation Kit # 344270KITW to properly mount the vent to the roof of the trailer and seal...
view full answer... - How Does Exterior RV Shower Box Install on RVThe Exterior RV Shower Box # 324-000061 that you referenced has 10 small bolt holes that are around the perimeter of the mounting bracket which most will use wood screws with. You'll want to cut the opening needed in the siding of your camper, then use some 2 inch by 2 inch boards to create a frame just behind the opening so that you can drill through the siding into wood to secure the shower in place. You'll also want to use butyl tape to seal the enclosure to the siding. For that we...
view full answer... - Install Kit Recommendation for the Fan-Tastic Vent Roof Vent w/ 12V Fan # FV801250The Fan-Tastic Vent Roof Vent w/ 12V Fan # FV801250 would only need the Installation Kit # 344270KITW. This comes with sealant and install screws to secure it to your trailer.
view full answer... - Can The Camco RV and Enclosed Trailer Roof Vent Cover Be Installed Off-CenteredInstalling the Camco RV and Enclosed Trailer Roof Vent Cover w/ Detachable Louvered Screen # CAM40453 a little bit off center shouldn't be a problem since the shape of the cover doesn't taper down too much on the sides. You'll still want to have the cover facing the correct direction though. A lot of RV vent covers with this design don't allow the factory vent cover to fully open any way so you will have no issues with it not fully opening if it ends up touching the cover due to it being...
view full answer... - Install/Sealant Kit to Use When Installing Fan-Tastic Roof Vent # FV800900You will need to use a sealant when you install the Fan-Tastic roof vent part # FV800900 that you referenced. For that we have the Roof Vent Install Kit part # 344270KITW which comes with all of the sealants you would need plus screws to attach the vent. I attached an install video that uses this kit on a similar roof vent for you to check out as well.
view full answer... - Install Kit Recommendation for Fan-Tastic Vent Roof Vent FV801250For an install kit that comes with sealant to use with the Fan-Tastic Vent Roof Vent # FV801250 that you referenced we offer the # 344270KITW which comes with fasteners and a urethane sealant.
view full answer... - Troubleshooting Separated Siding at the Joints of the TrailerThe Camco RV Vinyl Trim Insert # CAM25262 will replace your trim and allow you to have a nice molding. It is not intended to seal your walls, but to simply give you the finished look. This trim is intended to slide into existing metal track that is holding the siding in place. Since your aluminum sides are separating, I recommend using the Installation Kit with Screws and Sealant # 344270KITW to seal the siding from water and also secure it in place with the screws. I recommend removing...
view full answer... - Kit Needed to Install Fan-Tastic Vent Roof VentWe have a kit made for installing roof vents, including the Fan-Tastic Vent Roof Vent # FV802250. What you need is the Roof Vent Installation Kit # 344270KITW. This kit does include butyl tape, which you'll need, as well as sealant and screws. This kit will work for you no matter if your roof is metal or rubber. I have added a link to a video review of this kit for you to check out.
view full answer... - Roof Vent Install Kit Recommendation for RV with Fiberglass RoofSince you have a fiberglass roof the RV roof vent install kit you'd want is the part # 344270KITW. The Butyl tape kit you mentioned # CAM25013 is for use with rubber roofs or sidewalls so it would not work for you.
view full answer... - Can Existing Holes from Old Vent Assembly be Used for Hardware to Install Fan-Tastic Roof VentAs long as the holes where the existing screws are at are in good shape and they aren't too big for the recommended #8 screws that come in the installation kit # 344270KITW there should be no problem in using the same holes to install the Fan-Tastic Vent Roof Vent # FV801208.
view full answer... - Can Fan-Tastic Vent Roof Vent w/ 12V Fan FV807350 Be Installed In RV Roof That Is Sloped?As long as the slope you mention in your RV's roof is a flat slope and not a dome, you can absolutely install the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote - Powered Lift - 14-1/4" x 14-1/4" # FV807350 and will have no issues. I do recommend using the Roof Vent Install Kit # 344270KITW to make sure you have no leaks after installing the new vent. I included videos of the products mentioned for you to take a look at.
view full answer... - Where to Apply Caulk When Installing Trailer Roof VentYou would want to run a bead of the sealant around the vent opening on the underside of the mounting flange as shown in red on the photo I edited for you. Put the vent into place, pressing firmly so that the sealer spreads to the area around the mounting holes so that they are sealed when the vent is screwed into place.
view full answer...
- Roof Vent Installation Kit Recommendation For Using a Solar Panel Roof VentThe install kit we often recommend for roof vents like the # UF53-945001 is the part # 344270KITW. This will seal the vent to the roof of your trailer so that it won't leak after installing the vent.
view full answer... - Roof Vent for a 1968 Streamline Travel TrailerWe have several vents that might work for your Streamline trailer but nothing that is made specifically for it. I have included a link to the right to the options for you. Most of the vents require a 14-1/4 inch square opening to install the vent. The majority of the vents have plastic lids with a few exceptions that have metal lids. Beyond that it is just a matter of the color you want: white, blue, smoke, silver, clear, and metal. I also recommend the vent installation kit # 344270KITW.
view full answer... - Can the Ventline Vanair Trailer Roof Vent Be RivetedIf you like, you can use rivets with the Ventline Vanair Trailer Roof Vent part # VP-543SP as I don't see too much of a problem with this. That said, there isn't anything going to be pulling on the vent so standard self-tapping screws like what is included with the Roof Vent Installation Kit part # 344270KITW would work just fine as well.
view full answer... - Recommended Jackknife Rv Sofa and Roof Fan for Ram Promaster City WagonThe longest jackknife RV sofas we carry are 68 inches long. I've linked our selection so you can review the available options. For a roof fan on your Ram Promaster I suggest the Ventline Vanair Trailer Roof Vent # VP-543SP becuase of its small round design. Even though it's only 6-1/4 inches in diameter it will still circulate 100 cubic feet per minute of air. Use Installation Kit # 344270KITW to install and seal the fan.
view full answer... - Replacement Roof Vent Cover For Haulmark TrailerMany of the trailer roof vents use a standard 14-1/4 x 14-1/4 inch rough opening. The vent cover you choose will depend on the hinge style. I have attached three photos of roof vent covers that shows the hinge styles. Check out the vent on your trailer and see if it matches any of the three in the photos and that will make it easier to find a replacement. I have also attached a link to the vent covers and vents we offer. If you decide to replace the vent altogether you can check out...
view full answer...
- Recommended Cover for Powered VentWith your vent mounted sideways, you can use a cover like the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover - 23" x 19.5" x 10.25" - White # FVU1500WH to keep the rain out when you are camping. However, covers are not intended to keep water out when traveling if mounted sideways because it will not be aerodynamic enough. My recommendation would be to remount your bath vent to face the rear when open to allow you the aspects of traveling with the vent open even in the rain. I recommend...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Jameson C
Video by:
Kathleen M
Video by:
Michael B
Video Edited:
Chris R
Updated by:
Mary K
Updated by:
Wilson B
Edited by:
Amanda M
Test Fit:
Shane H
Installed by:
Robert C
Written by:
Halie H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
8/31/2023
We always take reviews about the packaging seriously. I will have our Customer Service team reach out to you.