Switching Trailer from Torsion Axles to 3,500 lb Leaf Spring Axles
Updated 12/12/2022 | Published 12/10/2022 >
Products Featured in This Question
Question:
I am replacing torsion axles with spring axles and the spring perches are set on approximately a 3 degree angle, which will have the spindle centerline either rearward or forward of the tube centerline. When installing which direction should they be?
asked by: Kevin S
Expert Reply:
In order to replace torsion axles with leaf spring axles you'll first need to start with a hanger kit, if it's a tandem axle trailer then I recommend the Tandem-Axle Trailer Hanger Kit for Double Eye Springs part # APT5. This can then be paired with a set of leaf springs like the 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles part # e54SR. The only thing that's left is the axle like the Dexter Trailer Axle part # 35545E-ST-89. The axle has a left and a right side so you'll need to make sure you have this the correct way before installing. The axle also has a top and a bottom as well because of the bow, the leaf spring perches are welded to the bottom therefore the axle is setup as an under sprung. If you need the axle setup as an over sprung then you will need to cut and re-weld the leaf spring perches on top of the axle.
I have attached our full axle selection below as well if this one is not the correct length for your needs.
I'm not quite sure I understand what you are talking about with the axle center-line but if you can explain this better I'd be glad to try and assist.
Product Page this Question was Asked From
Tandem-Axle Trailer Hanger Kit for Double Eye Springs - 3-1/4" Tall Front/Center/Rear
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Tandem Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer axles
- Search Results: trailer axle
- Search Results: trailer axle kit
- Shop: Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies
- Shop: Curt Double Lock Underbed Gooseneck Hitch w/ Installation Kit - 30,000 lbs
- Shop: Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit - 30,000 lbs
- Shop: B&W Turnoverball Gooseneck Custom Installation Kit for Chevy/GMC
- Shop: Kenda Karrier KR53 ST225/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 6 on 5-1/2
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Video: Complete Breakdown of the Dexter Nev-R-Adjust Electric Trailer Brake Assembly
- Video: Setting Up Your MORryde Standard Frame Hanger X-Factor Crossmember - 2018 Grand Design Reflection Fi
- Video: Review of TruRyde Trailer Leaf Springs - Double Eye Springs - TRU32FR
- Search Results: shock absorber kit
- Search Results: trailer brake shoes
- Search Results: trailer brakes
- Search Results: trailer hubs and drums
- Q&A: Changing 3,500 Pound Trailer Axles to 5,200 Pound Axles
- Q&A: Leaf Spring Recommendation for 2015 Shorelandr that is Rust Resistant
- Q&A: Where Are 25-1/4" Long 5-Leaf Double-Eye Spring for 6,000-lb Trailer Axles Made
- Q&A: Recommended MaxxFan Deluxe Roof Vent w/a Thermostat
- Q&A: Trailer Axle with 92 Inch Hub Face and 80 Inch Spring Center
- Video: An In-Depth Look at the Single Axle Trailer Fender for Boat Trailers
- Shop: Trailer Wiring
- Q&A: Replacement Dexstar Trailer Wheel with 17-231 Sticker
- Q&A: Options for New Bearings for Trailer Hub with 30205 Bearings
- Video: All You Need to Know About the Grease Seal
- Video: Spindle Grease Seal Set for L44643 Inner Bearing and 1.980 Bearing Buddy Spec Review

