Are Factory End Links Sufficient With Hellwig Front Anti-Sway Bar on 2021 Ford E-450 Class C

Question

Question:

I am purchasing the Hellwig. HE26GR front anti-sway bar for my2021 Ford E-450 class c . I would also like to replace the factory end links , any suggestions on something that Woud be an upgrade over factory , or are the oem links sufficient

asked by: Tom

0

Expert Reply:

Hey Tom! The factory end links on your 2021 Ford E-450 are perfectly fine to reuse with the Hellwig # HE26GR. The kit includes upgraded polyurethane bushings and new hardware, so the only thing you aren't replacing is the end links themselves.

On the E-450 chassis, the sway bar is where you see the biggest improvement in handling and stability. The OEM end links from Ford are already pretty heavy-duty, so there isn't a huge advantage to replacing them unless the originals are worn out.

What kind of Class C do you have?

expert reply by: Robin H

0

Hellwig Front Anti-Sway Bar
(click to enlarge)

Tom

5/26/2026

I have a 30 foot Thor Chateau on a 2021 Ford E450 Super Duty Thanks for the reply , I will keep the Ford oem end links on the Hellwig anti sway bar . The end links are a very easy part to change if need be later

Robin H.

5/27/2026

@Tom sounds good, you're welcome. If you need anything else don't hesitate to reach out.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Are Factory End Links Sufficient With Hellwig Front Anti-Sway Bar on 2021 Ford E-450 Class C

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching