Recommended 1/2"-20 60° Conical Cone Lug Nut that's 1-1/2" Long Overall

Question

Question:

I was wondering if you could tell me the length on some lug nuts.. Part Number TA66QR I have a customer looking for 1/2 inch 20 lug nut 1.5 long ,chrome with a Conical seat, closed.. Thank you

asked by: SPRING R

0

Expert Reply:

Hey Spring welcome back! The 1/2"-20 Taskmaster Trailer Wheel Lug Nut item # TA66QR has a 1-3/8" overall length. This is a 60° conical cone lug nut and is chrome plated.

For a 1-1/2" long 1/2"-20 lug nut, you'll need the Lionshead item # LHLR103. These are sold individually and also have a 60° conical cone. It has a stainless steel cap to prevent corrosion.

If you have any additional questions, go ahead and click on the box that says Add Comment and I'll be happy to answer them.

expert reply by: Jerred H

0

LHLR103
(click to enlarge)

Matt

5/23/2026

I bought a full set of the LHLR103 lug nuts to replace the lug nuts on my RV. These lug nuts are designed to work with the wheels on my RV. Note use a torque wrench to tighten the lug nuts. Do not over torque (could damage wheel and round the edges on the lug nuts. Do not use an impact wrench. Etrailer provided a great service with quick delivery and answering my questions.

Jerred H.

5/23/2026

@Matt Thanks for the tip and the kind words Matt! I appreciate you taking the time to leave that feedback!

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Recommended 1/2"-20 60° Conical Cone Lug Nut that's 1-1/2" Long Overall

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching