Looking For Replacement Motor For Jack

Question

Question:

I need a replacement motor for one of my jacks. I purchased these years ago and now one of them wont work unless I tap it with a hammer

asked by: Wade S

0

Expert Reply:

Hey Wade, thanks for reaching out. We may have a replacement motor for your jack, but they are largely brand and model specific, so I'll need to know exactly which jack you have. That way we can be sure you are getting the right thing.

Do you know the brand and model number of your jack? Or the model number of the motor? A lot of time the motor itself will have a sticker showing the brand and model number. Shoot me that info when you get a chance and I'm happy to look into it and see if we have what you need.

expert reply by: Jesse M

0

Wade S.

5/8/2026

I'm sorry for the lack of information, I purchased the ultrafab dual 12,000 lb jacks.

Jesse M.

5/8/2026

@WadeS Ok gotcha! I did see you were looking at those I just wanted to make sure we were on the same page. We do have a replacement motor for the Ultra-Fab 12K jack. For that you'll need the following: - Replacement Motor Gear Assembly for Ultra-Fab Deluxe Fifth Wheel Landing Gear # UF17-750007-003

Earl H.

5/11/2026

I purchased this replacement motor in 2024. It mounted exactly as OEM on jack leg, It operated quietly and I would purchase this product again.

Jesse M.

5/11/2026

@EarlH Nice! Glad to hear the motor is working out. Hopefully you don't need to buy another one anytime soon! We are here for you if you need anything though.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Looking For Replacement Motor For Jack

Product Page this Question was Asked From

Continue Researching