Recommended Low Profile RV Roof Vent

Question

Question:

Good evening. I have Dodge B250 van and currently have a standard rv roof vent. From ground to the roof vent top it is exactly 84. I am looking to change the roof vent to a lower clearance roof vent that will allow entrance into a standard residential garage 84. Looking for a low rise roof vent that will allow overall clearances less than 84

asked by: Mike G

0

Expert Reply:

Hey Mike. The shortest roof vent we have is the Ventline Ventadome Trailer Roof Vent -item # V2110SP-24. It extends only 2" above the roof when closed and fits a standard 14-1/4" x 14-1/4" roof opening. This is a manual roof vent.

We also have some powered options that include a fan like the Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid item # MA00-04751KSX. This fan would replace an existing MaxxAir MaxxFan and would be operated by your existing controls. It extends 3-3/4" above the roof.

What model roof vent do you currently have installed in your Dodge van?

expert reply by: Jerred H

0

V2110SP-24
(click to enlarge)

Answer 1

Hey Lessa. I've got a puck light that's pretty close to your current one. It's the Warm White Glantastic item #328-K-58L34P9. This is a 4-1/4" diameter x 1" deep puck light that fits a 3-3/8" diameter x 3/4" cutout.…

view full answer...

Answer 2

Hey Randy, congrats on the new Bronco. You're definitely going to need to jump up to a heavy rated tow bar. Like you said the Roadmaster Falcon 2 item #RM-520 tops out at 6,000 lbs and your Bronco's already over that sitting there empty. I…

view full answer...

Answer 3

Hey Alan, yeah you could swap the puck lights that you have now with ones that have switches like the part #277-000489 but the trick is getting the same size as what you have now which we don't have a way to look that up. This puck light is 4-3/8…

view full answer...

Answer 4

I spoke with the manufacturer, Command Electronics, about the 12V RV LED Puck Light #CE68ZR and found that it has a warm white - 3,500 kelvin rating.

view full answer...

Answer 5

No, the Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars #RM-035-1 would not fit your 1-3/16" thick mounts so you would need to go with a standard base plate. If you have a Ford Performance Heavy Duty Modular Bumper…

view full answer...

Answer 6

We have exactly what you will need. I spoke to my contact at Roadmaster and he informed me that you have two options depending on the braking system of the tow vehicle. Either you will want part #RM-9060-900002 for if your RV has hydraulic brakes or…

view full answer...

Answer 7

Hey Chip, yes I agree the metal lid of the Ventline Ventadome part #V2110SP-24 is going to hold up the best over time which would mean you wouldn't have to worry about replacing the lid for a very long time. How old is the trailer?

view full answer...

Answer 8

Most slides have EPDM rubber roofs but because EPDM is rubber it requires treatment each year to keep it soft and prevent shrinkage. You could replace it with TPO which is another synthetic rubber that will last longer than the EPDM. The smallest…

view full answer...

Answer 9

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 10

It looks like your Sundowner roof vent is a standard 14 x 14-inch size with a continuous-type hinge. For such a vent we offer the Ventline Vent Cover for Old Style Rounded Dome Trailer Roof Vents #BV0554-03 (smoke) and #BV0554-01 (white). We also…

view full answer...

Answer 11

Hey Greg, thanks for reaching out. So we do offer a few other 9/16" - 18 wheel studs that will be of sufficient length. The spline diameter of our studs is 0.689" though. We have nothing in that size with a 0.617" spline diameter or…

view full answer...

Answer 12

I walked out to our warehouse and pulled the Ventline Ventadome Trailer Roof Vent, part #V2110SP-24, from our inventory to measure. The outside edge of the vent flange measured approximately 16-1/2 inches square. The actual opening of the vent…

view full answer...

Recommended Low Profile RV Roof Vent

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching