Will Curt Trailer Hitch Fit 2013 Ford Focus ST With Center Exhaust

Question

Question:

I have a 2013 Ford Focus ST does this work with the center placed exhust system? Does any modifications need to be done? Thanks

asked by: Richard C

0

Expert Reply:

Hey Richard! Yes, the Curt Trailer Hitch # C11431 will fit with your center exhaust. I attached a picture below showing it installed with the exhaust like yours. You will have to drill two holes in the frame for the installation of the hitch.

What will you be using the hitch for?

expert reply by: Robin H

0

Curt Hitch
(click to enlarge)

Richard C.

12/23/2025

Hi Robin Looking into the Kuat 2.0, pro X or Thule, carrying 2 EMTB about 53 pounds each with batteries. Does the Curt come with differnt reciever sizes, I am leaning towards a 2". Thanks

Robin H.

12/23/2025

@RichardC the Class I # C11431 with a 1-1/4" receiver is the only option for the ST with that exhaust. You will also need stabilizer straps # 18050. You can use the Kuat Piston Pro X # KU48VR for 1-1/4" receivers and you won't be over the 200 lb tongue weight capacity of the hitch. Make sure you verify the capacity of your vehicle as well.

David H.

12/24/2025

@RichardC We put this on my son's 2014 ST. It fits right between the tail pipe and the bumper so it is limited on what fits into the hitch. I have a KUAT rack that goes down to the 1 1/4" that won't fit on there because where the rack sizes up to the 2" part it doesn't have room to slide all the way into the hitch. It is less stable than a 2" but I haven't found a 2" for a car in my searches. I have one on my Honda Accord also but we only care analog bikes as of now but have had 3 full suspension mtn bikes on there at times that would be about 90ish lbs.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Will Curt Trailer Hitch Fit 2013 Ford Focus ST With Center Exhaust

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching