How Long are Blue Ox TrackPro Spring Bars

Question

Question:

How long are the 13000 sway bars?

asked by: Ken H

0

Expert Reply:

Hey Ken, the Blue Ox TrackPro spring bars # BLU32FR that you referenced are 31 inches. Do you have a frame rail clearance issue where standard length bars won't fit?

expert reply by: Jameson C

0

Jameson C.

12/8/2025

Hey Ken, did the 31-inch Blue Ox TrackPro spring bars give you the clearance you needed around the frame rails? Sharing how they fit could help others working with tight setups.

Answer 1

Yes, you should swap the weight distribution bars to the 1,000-lb Spring Bars for Blue Ox TrackPro #BLU52FR. These have a tongue weight capacity of 800-1000lbs. It is important to use the correct bars with the TrackPro since the sway control and…

view full answer...

Answer 2

Since you already have the #BLU77FR you will not need to buy an entirely new system. You can swap out the spring bars with the #BLU32FR, but I would not recommend it. Switching to these spring bars would give you a tongue weight range of 1,000-1,300…

view full answer...

Answer 3

I would recommend that Blue Ox TrackPro #BLU77FR simply because it does not have lift chains like the SwayPro #BXW1006. Both will do a great job but the TrackPro will have a little less movement because of the absence of drop chains. Blue Ox is a…

view full answer...

Answer 4

Blue Ox has an easy system for determining the weight capacity of your spring bars, whereas other companies may use measurements or printed capacity to assist. With Blue Ox, there is a 5 dimple system: No dimples means it is rated for up to 350 lbs…

view full answer...

Answer 5

The Clamp-On Lift Brackets for Blue Ox SwayPro Weight Distribution Systems #BXW4010 is not the best option for a C-channel frame. Instead I recommend the Blue Ox Signature Series Lift Brackets for SwayPro Weight Distribution Systems - Clamp On or…

view full answer...

Answer 6

Hello David, good question. In my experience, it will be best to cut the holes for the vents before you lay down the membrane. That way you can cut away the membrane using a razor knife and get a good clean cut. If you tried to cut the roof and the…

view full answer...

Answer 7

After speaking with out expert install team I would NOT recommend patching or replacing only part of the membrane. It will just set you up for future leaks and other problems where the seam will be. Since you will have to remove the trim around the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How Long are Blue Ox TrackPro Spring Bars

Product Page this Question was Asked From

Continue Researching