Is The 30 Amp SmartPlug Available With 90 Degree Downward Connector?

Question

Question:

Is the 30 amp SmartPlug available with a 90 degree downward connector?

asked by: Paul G

0

Expert Reply:

Hello Paul, thanks for reaching out. For the 30 amp SmartPlugs, I am not seeing they offer one with a 90-degree connector. They would all be straight plugs like the part # SM77FR you were looking at.

expert reply by: Jesse M

0

Paul H.

11/6/2025

Thank you for your response. I will wait to consider purchase until a 90 degree connector model is available.

Answer 1

Hey Kerry! The SmartPlug RV Power Inlet and Connector item #SM77FR only has the one mounting plate that you can see in the attached picture below. The mounting screws install underneath the front cover and it is rated for marine use not just RV. I do…

view full answer...

Answer 2

Since your battery bank would essentially be rated for 210 amps the 45 amp rated Progressive Dynamics Inteli-Power RV Converter and Battery Charger #PD9145ALV that you referenced would fully charge both of them in about 4 hours or so. But that would…

view full answer...

Answer 3

Hey Bernie, it sounds like you are asking if a 30 amp cable could be wired to the SmartPlug Connector Plug Assembly for RV Power Cords - 50 Amp Female #SM36FR that you referenced. Yes you could do that or if you wanted to wire it to a 30 amp dog bone…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Is The 30 Amp SmartPlug Available With 90 Degree Downward Connector?

Product Page this Question was Asked From

Continue Researching