How to Install Redarc Tow Pro Liberty in 2024 Nissan Pathfinder with Factory Wiring

Question

Question:

I would like to install a tow-pro Redarc in my 2014 Nissan Pathfinder platinum with factory installed wiring harness. Is thei possible without making a lot of changes in the factory wiring harness. Thank You

asked by: Paul F

0

Expert Reply:

Hey Paul, in order to install the Redarc Tow Pro Liberty part # RED52VR in your 2024 Nissan Pathfinder you would need the install harness part # C51382 which will plug in under the dash of your Pathfinder preventing you from having to do any splicing or hardwiring.

You will need to cut off the black end of the harness I mentioned and wire it color for color to the universal harness that comes with the Redarc.

What are you towing?

expert reply by: Jameson C

0

Jameson C.

12/1/2025

Hey Paul, how did the wiring go with the Redarc Tow-Pro Liberty and the Curt harness in your Pathfinder? Your update could make it easier for others looking to keep their factory wiring intact. What trailer did you end up towing with it?

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

How to Install Redarc Tow Pro Liberty in 2024 Nissan Pathfinder with Factory Wiring

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching