25 Maxx-D Gooseneck Trailer Hydraulic Jack Recommendation
Updated 10/07/2025 | Published 10/02/2025
Question:
Hi Im looking to upgrade my 25 MaxxD roll off gooseneck trailer. but not finding a kit that will work with the existing 2 way pump. would like help finding the correct part or parts needed thanks.
asked by: Emmanuel S
(click to enlarge)
Expert Reply:
Hey Emmanuel, thanks for reaching out!
The Atlas IV Double-Acting 10K Hydraulic Trailer Jack # ST74VR is what you're looking for. It comes with a connection kit that hooks up to and allows you to control the jack via your dump trailer controller.
This has a 4-bolt bracket as opposed to 3-bolt bracket that you currently have on your trailer, but you should only have to drill 1 set of additional holes per bracket as the bolt holes are spaced 2" apart on center.
Do you plan on doing this installation yourself, or having a shop take care of it for you?
(click to enlarge)
Product Page this Question was Asked From
Atlas IV Double-Acting 10K Hydraulic Trailer Jack w/ 48" Connection for Dump Trailer - Bolt-On
- Trailer Jack
- Dump Trailer
- Enclosed Trailer
- 5th Wheel Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- 9001 - 10000 lbs
- Hydraulic Jack
- 26 Inch Lift
- Bolt-On
- With Rectangle Foot
- Stillwell
more information >
Continue Researching
- Shop: Atlas IV Double-Acting 10K Hydraulic Trailer Jack w/ 48" Connection for Dump Trailer - Bolt-On
- Search Results: trailers accessories and parts
- Search Results: trailer steps
- Search Results: trailer jack
- Search Results: trailer leaf springs
- Search Results: trailer lights
- Search Results: tarps
- Search Results: dump trailer tarp
- Shop: Atlas IV Double-Acting 10K Hydraulic Trailer Jack w/ 39" Connection for Dump Trailer - Bolt-On
- Shop: Stillwell NeXgen Zero Leak 6-Port Hydraulic Ball Valve
- Video: Review of Stillwell Trailer Jack - Hydraulic Trailer Jack - ST74VR
- Shop: Atlas IV Double-Acting 10K Hydraulic Trailer Jack w/ 60" Connection for Dump Trailer - Bolt-On
- Shop: Pacbrake Alpha HD Pro Air Bag Suspension Kit w/ Internal Jounces - Rear Axle - 5,000 lbs
- Shop: Suspension Enhancement
- Shop: Timbren Rear Suspension Enhancement System
- Shop: Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Coil SumoSprings Custom Helper Springs for Coil Spring Suspension Spec Review
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: BOLT brand vehicle and hitch locks
- Video: Installing the EcoHitch Hidden Trailer Hitch Receiver on a 2025 Hyundai Ioniq 5
- Shop: Grille Guard
- Q&A: Replacement Arms for Roadmaster MX Base Plate Kit for 2008 Jeep Wrangler
- Shop: Base Plate for Tow Bar
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Jack
Emmanuel S.
10/4/2025
Hi Jon thanks for the reply. I was looking at that setup but my issue would be the switch valve that would change between the dump cylinder and the jack. Since I would have 2 hydraulic jacks I would need to tie in both right?that would mean 8 ports? 2 each jack 2 dump cylinder 2 to the pump? unless there is another adapter I may need? Also I would be doing the install myself, I have installed a previously a single hydraulic jack on bumper pull. Thanks!