To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When heavy trailers or bed loads make the rear sag, the Timbren Rear Suspension Enhancement System adds up to 3,600 lbs of extra support right where it’s needed. These hollow rubber springs sit above the rear axle to help keep the vehicle level and improve steering and braking control when towing or hauling gear. The progressive design lets them flex easily under light loads, then firm up automatically as weight increases, keeping your ride height consistent and handling predictable.
Every bump or uneven road surface can rattle your vehicle and gear. The Aeon hollow rubber springs act like built-in shock absorbers, taking the brunt of road impacts so your factory suspension doesn’t have to. They cushion light loads for a comfortable ride, then stiffen under pressure to reduce bounce and bottoming out on rough roads. The result is less wear on your suspension and a smoother drive when loaded or empty.
When a curve or crosswind tries to push your ride around, each Timbren spring works on its own side to keep things balanced. This independent action helps control body roll during cornering or swerving and steadies off-center loads. Even if one side of your cargo is heavier, the springs respond individually to keep the vehicle planted and stable on highways or winding roads.
Adding serious load control doesn’t have to be complicated. This kit bolts onto existing frame rails above the rear axle using vehicle-specific brackets and hardware—no drilling required. It replaces the factory bump stops, so installation is quick with basic tools and no air lines or adjustments to worry about later. Once mounted, the system works automatically every time you load up, giving you reliable performance trip after trip.
Do not exceed the vehicle's weight-carrying capacity.
Customer Satisfaction Score:
91% were satisfied with this product
9% of customers were not satisfied
Ratings & Reviews
Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!
Great product. The ride and body roll at the rear axle are notceably improved (1989 Ford E350 Class C RV , 27 ft). I give it 4 stars because the installation was slightly complicated due to the rear brake lines needing to be slightly bent to provide clearance for the U bolts supplied in the kit. Great product and wish it came in a 5000 lb version.
2,000 miles in on a trip from the east coast to the Canadian Rockies these work great while loaded and towing. Close to zero bounce while towing, I love them. Unloaded, however, the ride in my 2026 Tundra has gone south. There is a noticeable, abrupt stop of the units hitting the axle when going over any kind of bump. When I get home and back to regular driving, I may just take them off, its that bad.
I've had these on our tow rig for a year now and I added buy them again today if I needed them.these have worked much better than airbags for our coil spring rear suspension to handle the tongue weight of our trailer. The SUV sits level when the trailer is on and it handles bumps and sway better than the airbags did providing much more comfort to us in the vehicle. Unloaded, we don't really notice they are there, unless, we have all the kids and some friends loaded up and you will fell them work when going over bumps.i do all my maintenance on the vehicle's and inspect these regularly and I cant see any wear so far even though we've gone on 6 trips with our trailer with about 5000 miles doing so.
I cant say these are the best for every truck or SUV, but for ours it is the best and I definitely would recommend to others.
Well they are exactly what I thought it would be. Hard for me to say it's what I needed yet.
I installed them on a homemade trailer from a salvaged 2001 base model tacoma. Once I get finished building it out and have some weight in it I'll have a better idea. But from what I've seen so far on a couple test drives they should come into effect when needed.
For reference I building an Tacoma based trailer with an ARE Contractor topper with a Naturnest roof top tent on the very top. So to counter and sway these should be very helpful. At least I hope so. I'm not an engineer but I did stay at an Holliday Inn once.
The Timbren SES is a simple solution for rear squat when towing. When hitched to my 30' Airstream Globetrotter (8800 GVWR) with a tongue weight around 1200 lbs, my Silverado 2500HD had a bit more squat than is ideal. I shopped airbags but didn't want to spend ~$2K for the set up and didn't want the hassle of installation and forever chasing air leaks. The Timbren SES literally installs on the Silverado in about 15 minutes. So simple. No bags, no compressor, no wiring, no air lines, no leaks. And WAY less expensive to boot. Just returned form a 600+ mile trip and it towed flawlessly.
A very simple and straightforward installation once you get the oem bumper stops off (had a shop do that)
Timbren worked with me as I had a non OEM frame height (vehicle was lower than stock) to recommend the proper kit. Highly recommend contacting timbren if you are unsure of the proper kit to use. Ride is more stable. It does feel stiffer and less bouncy but am looking forward to seeing how it performs with my truck camper. Truck is a 1998 dodge ram 2500. Brake line over left side of axle needed to be secured to prevent damage.
The Timbren overload spring/bumper was east to install and did what it was supposed to do when I hitched up a camp trailer. These did not negatively affect the ride by any means and I don't have to worry about the troubles with air bags.
Stiffens and corrects kneel in rear end of 2023 Chevy Silverado 1500. You will notice a stiffening of the rear end suspension while unloaded, but it’s a fair trade off to prevent sagging and porpoising while towing. I found it easier to pull the rear wheels and work from the side than underneath the vehicle while installing.
The timbres bump stop is exactly the right height to meet the axel when the trailer is connected with all its weight onto the hitch. I have an Andersen weight distribution hitch and it levels out perfectly. The day picture is with the coach (Winn 2100bh) with factory equipment. The night picture is after the timbres are in place. Looks good.
It has been almost a year since I installed Timbren Suspension Enhancement Systems (DVF350 and DVR350R) on the front and rear of my 2003 Dodge RAM Van 3500. These bumpers replaced the OEM bump stops that were on my van. I like the Timbren bumpers much better than the OEM bump stops because they provide a progressively cushioned response for suspension compression when traveling over significant humps like speed bumps in a parking lot, or curb ramps into driveways. I did not like the abrupt stop the OEM bump stops provided when traveling over the same objects. I installed the Timbren rear bumpers first, and after a few months of use, I decided to add them to the front. In both cases, the front and rear Timbren bumpers were easy to install once the OEM bump stops were removed. Installation required reuse of the factory hardware. On my van, the Timbren bumpers are not always engaged. Under normal load and travel conditions the bumpers are relaxed and about 1/2” away from the suspension landing points. However, their presence is much appreciated and very noticeable when the van is carrying heavy loads or handling significant humps.
Absolutely Pleased with the TIMBRENS. They were easy to install, and took less than an hour to install both. I noticed a slight stiffness in the ride as the rear bounced over a bad roadway. Towing is great, with a nice level and smooth ride. I am glad that I did not order the heavier duty Timbrens, than what was recomended for my truck. I believe the ride would have been too stiff. If you look at the photos showing the timbrens, the truck is still lifted in the rear, so what you see is a big gap between the rubber, and the steal plate. When the truck is lowered, there's 1" of space as it should be. BTW, I have been purchasing from etrailer for years now, and I have to say that I have never had any issues with any orders. They are my go to folks for all of my vehicle suppension stuff and trailer stuff. You can't go wrong with buying from them.
My F53 was like driving a waterbed down the road. With the Timbrens, it’s a different vehicle. Should have installed them years ago. Etrailer is my go to for anything trailer. FAST shipping and prompt responses to questions or concerns.
2022 F250 Super Duty. Super easy to install. I have about 3/4" gap between the spring and the plate. Time will tell how they impact the ride quality and how much sag they mitigate with my 5th wheel hooked up.
Timbren Spring Helpers were exactly what I needed on my Tundra plus a spacer kit since I have a 3” TRD lift. They were packaged neatly, with proper hardware, and excellent instructions! They absolutely do exactly what they are supposed to do! Truck rides much better and helps level out the load!
I'm suitably impressed with the difference i feel.
I have about 250 lbs. of static load with my topper and Decked cargo system. This put my install gap with no spacers just under the reccomended 1 inch minimum.Then add a couple hundred more pounds hauling music gear 100 shows a year, and the stop is resting on the axle.
I feel the absorption of the Timbren material is better than the flimsy stock bump stops. More cushion.
Where i really feel the difference is in the stabilty of excessive side sway when turning while loaded.
I have a gig coming up that will involve some unpaved mountain roads to get there so I think i will have a real goid idea of how these Timbren's will perform.
Instalation took me about an hour at 11 p.m.
The product it of the highest quality in design and build.
And Etrailer is a company that I would not hesitate to buy from in the future.
Thanks Dee Dee.
You rawk!!
On the return trip from an vacation in the southwest I hit a "dip" in the local highway in AZ. One of the Timbren broke free and I saw it bouncing down the road behind me. When I removed the one that was still mounted, the T head bolt was bent and the Timbren was loose in the frame slot on the van. It was probably a freak accident, but I will likely try another bump stop that is not constantly in contact with the axle.
Victoria H.
2/21/2025
That does not sound like a good experience, Paul! These do have a limited lifetime warranty. I will make sure you receive the all information needed.
Great product!!
The quality of the product is of top-notch.I installed it on a 2017 Chevy express 2500 cargo van with no load , install was very simple.picture with no load.will edit with picture and comments when loaded with equipment .
I had trouble with my browser called and spoke with Karen. She took my order. Then turns out I had two orders of the same thing. Karen took the time to call my home and ask is I really wanted two of the same thing. Great company, great customer service. How many companies in today's world would have made the extra effort.
This is the second pair of Timbren I have bought. I love them. Used them on a 2010 Silverado, and now on a 2014 Express Van. Not only help the 'bottoming out' effect, but great for stability during towing and when fully loaded.
Brayton
8/11/2015
After a year I still like them for heavy loads. I have found the bottoming out when hitting a bump with no load painful and uncomfortable. I actually cut two coil off them to allow the normal suspension to work when having no load. They still work for heavy loads. They are not the panacea for suspensions, but they definitely work when you have a heavy load.
Easy install, video was helpful. I'm extremely pleased with the ride and the fact I'll never have to air up my bags. Good trade up. Thanks for all the fallow up calls and info from Lisa with Etraier. I do recommend Timbren springs and Etrailer to anyone carrying heavy loads and or towing.
Mark S.
1/11/2018
Still great
WHEN IT COMES TO LOAD CARRYING AND STABILATY WE AT OUR AUTO AND LIGHT TRUCK SHOP DONT CONSIDER ANYTHING ELSE BUT TIMBREN
Do you have a question about this Vehicle Suspension?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Glenn
10/15/2022
Works really well in our Roadtrek camper van. Reduced sway from wind and trucks and mountainous road conditions. Very happy!