Bumper Mounted RV Spare Carrier that Can Carry Dually Wheel

Question

Question:

I am looking for an rv bumper mount that folds and will accommodate a dually tire for a c-class. i do not want a hitch mounted one, bucause i frequently tow.

asked by: Corey P

0

Expert Reply:

Hey Corey, we have a bumper mounted spare wheel carrier with the part # BR56VR which is rated for use with dually wheels like what you have. It isn't folding though which I don't have anything like that at this time.

expert reply by: Jameson C

0

Jameson C.

9/29/2025

Hey Corey, did the bumper mounted spare wheel carrier work out for your needs? I'm asking because your experience could help others looking for a similar solution.

Answer 1

For your Optronics light part as2t216 we have found that the correct replacement lens is the part #AST60B.

view full answer...

Answer 2

The correct Replacement Operator Mechanism for your model 4751KS MaxxAir MaxxFan is part #MA10-20281K-1AF. If your fan lid is unable to open even manually, then this is the part you need to replace. The other part you referenced, #MA10A04751KS would…

view full answer...

Answer 3

We do carry the Dometic RV Water Heater #DMC74FR which you could use to replace your Atwood G6A-8E 6 gal RV Water Heater, but I highly recommend switching over to a tankless system like the Furrion RV Tankless Water Heater 60,000 BTU #FR98SR. This…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Bumper Mounted RV Spare Carrier that Can Carry Dually Wheel

Product Page this Question was Asked From

Continue Researching