Solution for Needing Replacement Lower Section of Ladder on RV
Updated 08/26/2025 | Published 08/22/2025
Question:
I have a broken lower section 6 steps which hangs on 2nd step of the upper section of a Christianson Industries, lower ladder 2255-40, which is no longer available. What are your suggestions for replacing it? Is there anything else you need? I can send a photo showing it broken on the right side just below the its 2nd step down where a brace to the back of my RV was. Repairing it?
asked by: Marshall C
Expert Reply:
Hey Marshall, most likely only solution will be an all new ladder but if the dimensions match the # SU77VR it would work which would be awesome. This has an overall length of 36" with the two 7/8" inserts spaced 11" on center. The 7/8" is the outer diameter of the pipe that will insert into the upper section of the ladder that you have now.
Product Page this Question was Asked From
Replacement Bottom Ladder Section for Surco Exterior RV Ladders - Qty 1
- Accessories and Parts
- RV Ladders
- Ladder Section
- Surco Products
more information >
Continue Researching
- Search Results: 75998
- Search Results: 118779
- Search Results: furrion rv camera system
- Search Results: backup camera
- Search Results: rv door locks
- Shop: Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen
- Shop: Kenda Karrier KR53 ST205/75R14 Radial Trailer Tire w/ 14" Black Spoke Wheel - 5 on 4-1/2
- Search Results: rv ladders
- Search Results: trailer brake controller
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Replacement Bottom Ladder Section for Surco Exterior RV Ladders - Qty 1
- Video: Review of the Replacement Bottom Ladder Section for Surco Exterior RV Ladders
- Shop: Better Bath RV Kitchen Sink - Double Bowl - 27-1/8" Long x 16-1/8" Wide - Stainless Steel
- Shop: Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Lug
- Q&A: Fit and Compatibility of PR6 Leaf Spring on a Trailer with Tandem Dexter 7K Axles
- Q&A: Dimensions of Surco Replacement Ladder Section SU77VR To Identify If Correct Replacement
- Q&A: Can Blue Ox Sway Pro System be Used in 2-1/2 inch Trailer Hitch
- Q&A: Replacement for iRV64FR Stereo System
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: How to Choose a Trailer Brake Controller
on Accessories and Parts
Marshall C.
8/26/2025
The lower section has 6 STEPS or ~72" lower section (vs. your 36") with curve from bottom to connecting plate against the back of the RV. and the top is a 2 square 'j' brackets that narrower than the rest of the ladder which has about ~ 12 1/2" outside width and ~ 10 1/8" inside width. Is there something else?