Is RackEm Fitz-All Enclosed Trailer Ladder Rack Installed Using Sheet Metal Screws

Question

Question:

Is it installed with sheetmetal screws?

asked by: Paul

0

Expert Reply:

This ladder rack comes will full instructions and installation hardware. To install use the provided self tapping stainless steel screws along with the plastic washers. The hardware you may decide to use can vary with the trailer shape and material.

expert reply by: Heather A

0

Answer 1

The weight capacity for the Rackem Trailer Cargo Control, part #RA-28 is listed at 400 lbs. This is the weight capacity for the complete rack, and not just one bar. When installing you need to make sure you have a solid place to secure the mounting…

view full answer...

Answer 2

Yes, we do have a roof rack that will work with the rounded roof on your Interstate cargo trailer. It is the Rack'Em Fitz-All Enclosed Trailer Ladder Rack item #RA-28. This roof rack has a 400 lbs capacity and mounts to the side of your trailer…

view full answer...

Answer 3

This Rackem Fitz-All enclosed trailer ladder rack system is intended for use on enclosed trailers with rain gutters. However, you may be able to adapt the installation as follows. Our installers have experience doing this in a similar circumstance.…

view full answer...

Answer 4

While the Rack'Em Fitz-All Enclosed Trailer Ladder Rack #RA-28 was designed to fit on trailer with a rain gutter, we have had several install it on their trailer without rain gutters. I have also included our review video below where you can see…

view full answer...

Answer 5

Yes. Based on the pictures you provided it does appear your trailer has rain gutters so the Rack'em Fitz-All Enclosed Trailer Ladder Rack #RA-28 will bolt on just fine. I included an installation video of the #RA-28 and a picture of the #RA-28…

view full answer...

Answer 6

For the Rackem Fitz-All Enclosed Trailer Ladder Rack, #RA-28, to fit your 2011 Haulmark HLC trailer, the trailer would have to be between 4-1/2 and 8-1/2 feet wide with rain gutters along each side of the roof. I have included a link to the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Is RackEm Fitz-All Enclosed Trailer Ladder Rack Installed Using Sheet Metal Screws

Product Page this Question was Asked From

Continue Researching