Looking For Replacement Lug Nut Cover For 2000 Newmar/Spartan Motorhome

Question

Question:

I have a 200 Newmar/Spartan motor home in need of a lug nut cover. I did find a close match on your site. Is it possible to forward pictures of wheel to confirm match? Thank u,

asked by: Pat S

0

Expert Reply:

Hello Pat, thanks for reaching out. There is no way to add pictures to the comments on here (yet) but you can go head and email pictures to me. My email is [email protected]. Send those over and I am happy to take a look. Also please let me know the diameter of your pug nuts. The Wheel Masters Lug Nut Covers # WM8012 for example fit 1-1/2" lug nuts.

expert reply by: Jesse M

0

WM8012
(click to enlarge)

Jesse M.

8/15/2025

Hey Pat, did you get a chance to send over the pictures of your motor home's wheel? I'm eager to help you find the right lug nut cover!

Pat S.

10/3/2025

@JesseM I'm sooo sorry for the delay in sending pictures of the missing motor home lug nut cover. We've had some health issues that took priority. Your picture looks correct. I'm attaching some information from Newmar, below which will be included in my email, hopefully with some good photos.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Looking For Replacement Lug Nut Cover For 2000 Newmar/Spartan Motorhome

Product Page this Question was Asked From

Continue Researching